0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is treatment procedure that uses a pulling force to prevent or reduice muscle spasm to keep a joint or other body part staionary or hold broken bones in place?
A treatment procedure that uses a pulling force to prevent or reduce muscle spasm, to keep a joint or other body part stationary, or to hold the ends of broken bones in place.
What is a front that is moving called?
A front that does not move is called a stationary front. There is only 4 types of fronts. There's a startionary front, a occluded front, a cold front, and a warm front.
Cold and warm front meet and cold front pushes wram front up and away is what type of front?
It is called a lower pressure front.
What are 4 kinds of fronts?
Cold front warm front and occluded front and Stationary front. They are right I have my science book right in front of me. lol
Is an occluded front a standard weather front?
it is not a standard weather front
Are animals staionary?
Only the dead or paralyzed.
Who is foult when some one get reverse in a junction?
if your vehicle is staionary (not moving) then the person who hit you is at fault
Where to get Reynolds trimax pen in Bangalore?
Try to find it on Avenue Road, Lots of whole-sell staionary product dealers are there, you might find this...
I am having problems with my 200sx when the car is worm it makes tapping noise only when staionary?
As a guess ... your lifters are "loose", need more oil, Miracle Oil, or just a cleaning.
What is shaping in lathe machine operations?
Although shaping usually refers to removal of material from a staionary object, material removed while rotary broaching with a Slater broach on a lathe is very similar to a typical shaping operation.
Who was the designer of the daimler reitwagen?
Gottlieb Daimler and Wilhelm Maybach in 1885. Based on their former employer's failed design (Niklaus Otto). Otto would eventually make staionary Diesel power plants and formed the Deutz company.
Why is playing with scissors dangerous when nothing happened to you when you tried it?
Its dangerous because scissors have feelings too and if you play with them too much they get annoyed and call the STAPELIA the staionary mafia who before throwing you to the bottom of the sea with photocopier toner shoes, will behead your calculator and put its head on your pillow.
What charges the battery on a ATV?
On the end of the crankshaft is a set of electrical windings that turns as the crankshaft turns ( known as the rotor ) . There are staionary windings mounted in the engine casing that do not turn ( known as the stator ) . this makes up your alternator and this charges the battery as the engine is running . Hope that answers your question .
What does a turbo nozzle ring do?
This is a staionary part of the turbo and converts the presure of the exhaust gases to kinetic energy, i.e. speed, and direct it to the blades which is the moving part of the turbocharger. Consequently, on the other end of the shaft there is the compressor which draws air and sends it with high pressure into the engine combustion chamber.
What would cause a 2001 Chevy Venture to blow warm air when moving but not when staionary?
Need to check the coolant level in the Radiator, it is probley low on coolant. The heater core could be 1/2 stoped up. Can switch the hoses around on the heater core and go drive it, It will flush the heater core.
A measurement of the motion of something. This is equal to the product of the moving objects's mass times it's velocity?
== == Momentum is the product of the mass of an object multiplied by its velocity (or speed). Momentum is conserved so if a moving object hits a staionary object the total momentum of the two objects after the collision is the same as the momentum of the original moving object.
R reg vauxhall corsa problem - why does your oil light keep flashing when staionary?
It is usually because the revs fall below 1000 rpm and they should not fall below this figure. If they are falling much below then its best to adjust the idle sensor so they stop falling below 1000 rpm, otherwise dont worry about it.
