0
12 lead out motor is generally with two different set of winding usually for double speed application. 6 lead connection is to enable star delta starter. With 12 lead the motor can be connected in star delta and for two speed application. It is better to explain with proper wiring diagram only so that no mistake is done.
Wiki User
∙ 6y ago
Add your answer:
Earn +20 pts
What size wire would you use to wire a motor that draws 16A from a circuit?
12
How do you connect the 12 motor leads to a 3- phase supply?
The 12 lead motor is a very versatile motor and can be connected in numerous ways. It is a dual speed motor and can be wired as star delta. If you are interested, start a Discussion Page and I will see if I can help you.
How do you power a 3 volt DC motor with a 12 volt battery?
you would have to put some type of resistor in the circuit with the motor...the resistor would have to be in series with the motor and would have to be of a high enough value to lower the voltage by 9 volts....There is a formula for working this out but you would need the amperage of the motor to figure this....
What is the difference between control circuit and power circuit?
The power circuit begins at the wall. The control circuit comes in over the cable. If you touch the power circuit, you get a shock. If you touch the wire from the cable, nothing happens. The power contains the power to give the light to the television screen. The cable tells it what picture to show. Now, if you look at your Circuit diagram, you will see where the power comes to the computer. It might say +5v or +12v or it could show and input of 110 volts and an output of +5 and +12. There probably is also a -5 and -12 somewhere. Those are your power circuits. They power the entire computer. If you look closely at your wiring diagram, a wire from that goes to every transistor in your computer. The control circuits are likely to go anywhere. They carry data. The power circuits all go back to one point. The control circuits do not.
What is the difference in wiring a 12 3 phase motor at low voltage between run and start?
You have to wire both the run and start windings. The start windings will automatically be removed from the circuit once the motor is at 75% of normal speed. The start winding gives you more torque to start the motor.
Which motor would have higher current flow 2 ohms motor in a 6 volt circuit or a 3 ohm momtor in a 12 volt circuit?
expecto patronum! ~:)
What size wire would you use to wire a motor that draws 16A from a circuit?
12
Where can a circuit diagram for an electronic power inverter be found?
This is a text-only site and was not designed to show circuit diagrams, but there are lots of circuit diagrams available elsewhere!Just put "power invertor circuit diagram" or similar wording into your favorite web search engine and you'll be given lots of links to them.A link to a very typical circuit diagram for a 12 volts dc to 230 volts ac invertor is given as a Related Link below this answer.
Can a integrated circuit chip of nine volt supply used with 12 volt motor and work properly while using with bettaryof 12 volt?
no
How do you connect the 12 motor leads to a 3- phase supply?
The 12 lead motor is a very versatile motor and can be connected in numerous ways. It is a dual speed motor and can be wired as star delta. If you are interested, start a Discussion Page and I will see if I can help you.
You have an 88 300zx and the blower motor does not work you have checked fuses and replaced the blower motor to no avail anyone have any suggestions?
You need to take a 12 Volt circuit tester and trace back from the motor; you must not be getting current. Test the switch and the ground to the motor also. Mark
What would happen if a 12 volt dc geared motor is run with 19 volts?
The motor would operate above its rated RPM. The motor would start to get hot as the current draw would be greater. This might eventually burn the insulation off of the windings and cause the motor to short circuit.
How do you power a 3 volt DC motor with a 12 volt battery?
you would have to put some type of resistor in the circuit with the motor...the resistor would have to be in series with the motor and would have to be of a high enough value to lower the voltage by 9 volts....There is a formula for working this out but you would need the amperage of the motor to figure this....
What size wire do you use on a fridge freezer?
12 gauge wire is used for household plugins, and 14 gauge wire is used for lights. So, 12 gauge is the size to use. But since a freezer has an electric motor, it is best to not plug anything else with a motor into the same circuit.
What is the difference between control circuit and power circuit?
The power circuit begins at the wall. The control circuit comes in over the cable. If you touch the power circuit, you get a shock. If you touch the wire from the cable, nothing happens. The power contains the power to give the light to the television screen. The cable tells it what picture to show. Now, if you look at your Circuit diagram, you will see where the power comes to the computer. It might say +5v or +12v or it could show and input of 110 volts and an output of +5 and +12. There probably is also a -5 and -12 somewhere. Those are your power circuits. They power the entire computer. If you look closely at your wiring diagram, a wire from that goes to every transistor in your computer. The control circuits are likely to go anywhere. They carry data. The power circuits all go back to one point. The control circuits do not.
How many circuit are there in the us?
12
Can I use a 30 amp circuit with a 12 gauge wire to handle a tablesaw that runs at 13 amps under load but spikes above 30 amps on turning on as the 20 amp circuit kept tripping at turn on?
This is proper connection for a motor that has a full load amperage of 13 amps. The wire size for motors has to be 125% of the full load amperage from the nameplate on the motor. On a 13 amp motor this relates to 16.25 amps. The next wire size up from this current is #12 rated at 20 amps. If you are using a fractional motor starter switch to control this motor, the heater size for the switch should have a rating of 16.25 amps. The fusing for wire is 40 amps for non time delay fuses, 25 amps for time delay fuses or a 30 amp circuit breaker.
