answersLogoWhite

0


Best Answer

single ended scsi is a method of transmitting electrical signals over wires. one wire carries a varying voltage that represent a signal, while other wire is connected to a ground. single emded scsi cables are of 6m-1.3m long.

Differential scsi is a method of transmitting information electrically by means of 2 complementary signal pairs sent on 2 separate wires.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

15y ago

The main difference between single-ended scsi and differential scsi is that the latter of the two is not single-ended.

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Difference between single ended scsi and differential scsi?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Why the peak value in double ended differential amplifier is double the peak value of single ended differential amplifier for the same input signal?

The peak output value in a double ended differential amplifier is double the peak output value of a single ended differential amplifier for the same input signal because there are two outputs, one being the normal output, and the other being the inverted output. Whatever the normal output does, the inverted output does, but with a reverse sign. As a result, if one output has a value of X, then then other output has a value of -X. If you compare the two outputs, then, the difference between them will be 2X, or double the value.


What are the two types of SCSI buses use in signaling methods?

1) Single-Ended signaling 2) Differential Signaling


What is the difference between installment credit and open ended credit?

the difference between installment credit and open ended credit is they are the same..


Find an expression for double ended differential amplifier gain?

from codi@humanoid.netdouble ended differential gain, also know as differential gain:Ad = (Vo2 - Vo1) / Vid = gm*Rd


What is single ended wrench?

You cant tell the difference with a normal and single handed wrench.....So...Nobody knows


Are all SCSI devices compatible with all SCSI ports?

No There are 2 electrical alternatives single ended SE and differential types. VD These cannot be used on the same bus. However a third type low voltage differential LVD can be if the interface card supports it


What is the difference between rs232 and rs485 port?

Difference between Rs232 and RS485 is Only Distance RS232 is not for long or far distance .. but RS485 can be use for LONGEST distance ..RS232 is single ended communication where as RS485 is Differential communication.Max.no of receivers in RS232 is only ONE, whereas in RS485 is 32.Max.no of transmitters in RS232 is only ONE whereas in RS485 is 32.IN RS232 there is no pin to change from transmitter mode receiver mode. But, In RS485 have DE pin to set transmitter mode and RI to set receiver mode.


Why is differential amplifier preferred over single ended amplifier?

The input stage of an op amp is usually a differential amplifier; this is due to the qualities that are desirable in an op amp that match qualities in a differential amplifier: common noise rejection ratio; low input impedance, high output impedance, etc. The use of differential amplifiers in op-amps is to increase the input range and to eliminate common entries like noise.


What statements identifies a difference between Richard the Lionheart and Charlemagne?

Richard the Lionheart’s major military campaign ended in a treaty, while Charlemagne‘s ended in complete victory. (APEX)


Why sepic called single ended converter?

Single ended is referred to converters with single switch topology. SEPIC has only one switch and hence named Single ended primary inductor converter. (Primary inductor because the inductor is charged during ON cycle of the switch) For example, There are double ended flyback topologies with two switches. It is named as double ended because it contains two switches.


Can you mix single-ended and differential devices on a SCSI subsystem Why or why not?

when differential signaling was first introduced you could not mix se and hvd devices because of the high voltage used in the hvd. since then a new signaling called lvd is used and it will allow you to use a se if you use the lvd/se mode.( p.1008 managing and maintaining your PC 5th edition)


How did Washingtons reaction to the Whiskey Rebellion underscore the difference between the Constitution and the Articles of Confederation?

he came in with the U.S. Army and ended the rebellion