making current is a peak value attain at first cycle when the circuit breaker is close.the making current rating is expressed in "peak" value of the maximum ac current it can safely close on that's why it is always have higher value than breaking current. Making current is limited by the withstand capability of the contacts.
Breaking current is based on the ability of the contacts to interrupt the current. If the contacts are not able to interrupt the current when they open, the heat energy in the resulting arc will often destroy the device. the breaking current rating is expressed in RMS value of the current.
It is usually printed on the circuit breaker in KA Killo Ampere. That is thousands of Amps.
Making capacity is the max fault current it can carry during closing of breaker, e.g. You are closing a breaker on fault. The making capacity is always higher because it is expressed in peak value not rms, and also because of the DC offset, voltage and PF while closing
Before making any changes to circuit breakers, make certain that the breaker does not exceed the capacity of ANY current carrying wire in the circuit. If you attempt to increase the size of the breaker in your condo, and exceed the capacity of the wire that is fed from that breaker, you WILL burn down the condo and when the fire department investigates the fire and finds out what you did, the association will be quite upset with you. Plus, it's against the law. If you need to make that kind of change to your electrical wiring, contact a qualified electrician to discuss options. You will also need approval of the Condo Association in most situations like this.
I haven't heard of this in relation to a breaker. Breakers will have ratings for short circuit interrupting, max voltage, line charging, etc. A load break switch will have a "breaking capacity", meaning it can be opened as long as the load current is below the breaking rating.
A circuit that has only a capacitor in it. Or the net reactance is below zero, making it capacitive. The current leads the voltage in a negative (capacitive) reactive circuit.
yes , it is required so that the leakage current from transformer/electrical windings to metallic enclosure of welding machine does not harm a person/operator & the current is rooted back to earth bajaj mahesh, asst fire & sec officer
When making an electrical connection on a stove, you should use a circuit breaker.
Hard to define... A four year old child has the strength to physically "make" a typical household circuit breaker, while a teen would be able to "make" a typical industrial circuit breaker. (The latter breaker being physically much larger than the former.) Circuit breakers have their "breaking capacity" rated in AMPS. A typical household breaker is rated at 20, 30 or 50 Amps. Industrial breakers might be rated at 500 amps or a thousand or even more. Hope this helps but if it didn't answer your question, please rephrase it and ask again.
Unintelligeable...say again in proper English.
Making capacity is the max fault current it can carry during closing of breaker, e.g. You are closing a breaker on fault. The making capacity is always higher because it is expressed in peak value not rms, and also because of the DC offset, voltage and PF while closing
Before making any changes to circuit breakers, make certain that the breaker does not exceed the capacity of ANY current carrying wire in the circuit. If you attempt to increase the size of the breaker in your condo, and exceed the capacity of the wire that is fed from that breaker, you WILL burn down the condo and when the fire department investigates the fire and finds out what you did, the association will be quite upset with you. Plus, it's against the law. If you need to make that kind of change to your electrical wiring, contact a qualified electrician to discuss options. You will also need approval of the Condo Association in most situations like this.
There are two important different parameters as far as the disconnection/connection of Electrical utilities is concerned.- Breaking capacity.- Making Capacity.In simple way the Load Break Switch used to cut off healthy circuits or to break / disconnect the load. As a precaution, normally the LBS / Isolator are to be switched on under no load, the connected load to be utilized after switching on the Isolator. This why it has no making capacity. Circuit Breakers are intended to operate under unnormal conditions in order to clear the fault & to isolate the defective circuits protecting its associated electrical equipment, therefore breaking and making capacities are considered as the most important criteria as far Circuit breaker are concerned.
By 'switching on an electrical appliance' we are completing (closing) the electrical circuit, allowing electricity to flow and the device to work.
Arcing is caused by a poor electrical connection. The breaker is not making good contact with the buss bar. Try replacing the breaker.
A "dedicated" circuit is one to which only one device is or can be connected; therefore the circuit is "dedicated" to the device. A NON dedicated circuit will therefore be one to which multiple devices can connect, such as the wall outlets in your home. Multiple wall outlets are connected to a common circuit breaker, making that an example of a non-dedicated circuit.
A switch is a means of making (on) or breaking (off) an electrical circuit.
I haven't heard of this in relation to a breaker. Breakers will have ratings for short circuit interrupting, max voltage, line charging, etc. A load break switch will have a "breaking capacity", meaning it can be opened as long as the load current is below the breaking rating.
I need help