Anecdote below aside, the equation is H2SO4 + H2O -> HSO4- + H3O+ ---- It depends on whether you add Acid to Water, or Water to Acid. Though Sulfuric Acid is highly soluble in water, if you add water to concentrated Sulfuric Acid it can boil, spit and splash out of its container. If you've never had burns from concentrated Sulfuric Acid, trust me when I say you never want to experience it. There is nothing quite like seeing the skin literally melt from your body, not to mention the pain.
It is therefore preferable to add the Acid to water in small amounts until the necessary amount of dilution is achieved. In all cases, be sure to wear a long sleeve shirt, eye protection (preferably a facial mask) and breather, plus chemical gloves. If you aren't near running water, ensure that you have a gallon of fresh water available for flushing any areas of your body that may accidentally come in contact with the acid. I'd also recommend wearing a hat.
In my case, I was wearing a ballcap, heavy long sleeve denim shirt, but since I was only moving the bottle, I wasn't wearing gloves or facial protection. The bottle slipped out of my hand and hit flat on the bottom when it hit the floor, causing the acid to spurt out of the spout. The cap wasn't on tight and had come loose. It is a miracle that it didn't get into my eyeball, though it did get the right side of my face, under my chin, all around my eye, and part of my ear. It completely destroyed and burned the denim shirt I was wearing, and caused a 3rd degree burn on my wrist. The ballcap saved me from having to shave my had also - if it had hit my hair it would've destroyed it as well.
The only thing that kept my injuries to a minimum was that I've worked in military and industrial areas all my life, and instinctively moved toward the laundry tub and water to flush out the acid. I had water flushing it within 30 seconds. According to the plastic surgeon I consulted, it's the only thing that kept the burns from being much worse. As it is, you can't tell except for lighter skin pigmentation. The worst scar is on my wrist where it literally burned down to the muscle.
----
Dilution, as long as you mix them properly
When sulfuric acid is mixed with water, a highly exothermic reaction occurs, releasing a large amount of heat. This reaction is used to dilute sulfuric acid for safety reasons, as adding water to the acid helps to control the temperature rise and prevents splashing or boiling of the acid. It is important to always add acid to water slowly and carefully to prevent violent splattering.
Carbon does not react with dilute sulfuric acid but does react with conc. sulphuric acid through redox reaction.
There is no reaction. In sulfuric acid the only molecule is the molecule of sulfuric acid itself, symbolized by the chemical formula: H2SO4.
Probably the most common one is C + 2S = CS2.
it bubbles up
Carbon doesn't react with acids.
C+2HCl=CCL2+H2
The reaction between copper oxide and sulfuric acid is a chemical reaction that results in the formation of copper sulfate and water. This is an example of an acid-base reaction, where the acid (sulfuric acid) reacts with the base (copper oxide) to form a salt (copper sulfate) and water.
The reaction between formaldehyde and sulfuric acid forms methylene bisulfate. This is a reversible reaction that can also produce bisulfite ions and water as byproducts.
The word equation for the reaction between magnesium carbonate and sulfuric acid is: magnesium carbonate + sulfuric acid -> magnesium sulfate + carbon dioxide + water.
The chemical equation for the reaction between sulfur dioxide and water to form sulfuric acid is: SO2 + H2O → H2SO3. The subsequent reaction of sulfurous acid (H2SO3) with water to form sulfuric acid is: H2SO3 + H2O → H2SO4.
The reaction between sulfur trioxide and water is called hydration or hydrolysis. It produces sulfuric acid as the final product.
The reaction between copper oxide and sulfuric acid is a chemical reaction that results in the formation of copper sulfate and water. This is an example of an acid-base reaction, where the acid (sulfuric acid) reacts with the base (copper oxide) to form a salt (copper sulfate) and water.
The reaction between formaldehyde and sulfuric acid forms methylene bisulfate. This is a reversible reaction that can also produce bisulfite ions and water as byproducts.
The word equation for the reaction between magnesium carbonate and sulfuric acid is: magnesium carbonate + sulfuric acid -> magnesium sulfate + carbon dioxide + water.
The chemical equation for the reaction between sulfur dioxide and water to form sulfuric acid is: SO2 + H2O → H2SO3. The subsequent reaction of sulfurous acid (H2SO3) with water to form sulfuric acid is: H2SO3 + H2O → H2SO4.
The reaction between sulfur trioxide and water is called hydration or hydrolysis. It produces sulfuric acid as the final product.
When concentrated sulfuric acid is mixed with water, a highly exothermic reaction occurs, releasing a significant amount of heat. This reaction is highly exothermic due to the strong attraction between sulfuric acid molecules and water molecules. It is important to add the acid to the water slowly and carefully to avoid splashing and potential hazards.
A neutralization reaction will occur between formic acid and sulfuric acid, leading to the formation of water and the salt called sodium formate.
The word equation for the reaction between magnesium carbonate and sulfuric acid is Magnesium Carbonate + Hyrdocholric Acid > Magnesum Chloride + Carbon Dioxide + Water.
The word equation for the reaction between lithium carbonate and sulfuric acid is: lithium carbonate + sulfuric acid → lithium sulfate + carbon dioxide + water.
Yes,they can undergo a neutralization reaction, the reaction between sulfuric acid and ammonia is feasible.
A neutralization reaction. Products are a salt and water. Between strong acids and bases.
It spits quite alot if you add H2SO4 to H2O