0
Using contactors (or relays) to control electric heat means
that all of the heat will be started at one time unless separate
time delay relays are used. Contactors are magnetic and
make noise. They snap in and may hum. Contactors are normally
used on commercial systems where they may not be
directly attached to the ductwork. This prevents the noise
from traveling through the system - Sequencer are cheaper and quiet compared to contactors.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Definition of coil in contactor?
The coil in a "Contactor" is essentially an electromagnetic coil that provides the driving force to close the contacts in a Contactor. When the "Coil" is energized by a lower control voltage usually from some type of controller such as a PLC, the Normally-Open contactor will close or in the oposite case, the Normally-Closed contactor will open.
What causes an electrical contactor to make a buzzing noise when activated and what should be done about it?
Contactor chatter can be caused by a broken shading ring winding on the pole face of the contactor. Low voltage to the coil can be another reason for contactor chatter. A constant hum on a contactor will be caused by misalignment to the two pole faces. Check for rust building up on the two surfaces.
Which side of a motor contactor should the overload contact be placed?
On the load side of the contactor. T1,T2,T3.
What is the difference between a motor starter and a contactor?
Motor started will have overloads the contactor connect es line voltage.
How do you wire contactor for two light circuits through a time clock?
How do you wire a time clock with a contactor with a override switch
How does magnetic contactor operate?
explain me about the contactor works with examples. if i want to control a motor with contactor. and how i can use contactor in loops with over load and circuit breakers.
When was Sequencer - Covenant album - created?
Sequencer - Covenant album - was created in 1996.
How do you calculate contactor capacity of star contactor?
metres
What is the difference between an definite purpose contactor and a lighting sontactor?
A definite purpose contactor is designed (and rated) for a specific load. So a lighting contactor is one example of a definite purpose contactor. A motor starter contactor is another example. So, a lighting contactor is a definite purpose contactor, but a definite purpose contactor is not necessarily a lighting contactor (it might be a motor starter, for instance).
Can you use an AC contactor in the place of DC contactor?
No, you definitely cannot.
How do you get subtitles if your making a level on littlebigplanet 2?
To make subtitles in LBP2, you will need a sequencer and a magic mouh. Place the sequencer somewhere and open up the circuit board. Then, place the magic mouth on the sequencer and tweak the mouth so "Subtitles" are on. Add text to the mouth and then connect a desired wire to the sequencer so it can be activated.
What is a loop-based sequencer?
boo
What usually cause the star contactor to burn on a star delta starter?
A lot of designers will fit an under rated star contactor, partly for cost saving purposes and partly down to the fact that the star contactor will only stay energised for a brief period. Burning out the star contactor could be down to it staying in circuit too long, not changing over to delta, a timer malfunction holding in the star contactor or switch that is defective in the control circuit. Another cause could be your motor is drawing excess current.
Definition of coil in contactor?
The coil in a "Contactor" is essentially an electromagnetic coil that provides the driving force to close the contacts in a Contactor. When the "Coil" is energized by a lower control voltage usually from some type of controller such as a PLC, the Normally-Open contactor will close or in the oposite case, the Normally-Closed contactor will open.
What is micro programming compare hard byte and micro sequencer control unit?
compare hard byte and micro sequencer control unit
How is a Blowout coil connected?
A blowout coil connected in series with contactor's auxiliary contacts that shunt around the main contactor contacts. The coil is out of the circuit when the main contactor contacts are closed and in the circuit when the main contactor contacts are open.
Who invented the DNA sequencer?
brock siegel
