0
In North America, it averages at 12 - so the best depends on your gap where you intend to place it. It's also cumulative - meaning that two twelves next to each other increase the rating.
It is the rating of a house's ability to Retain heat.
Wiki User
∙ 14y ago
Wiki User
∙ 11y agoR value is in fact the unit thermal resistance, it is derived from the ratio of the temperature difference across an insulator and the heat flux through it. therefore, the higher the value the better the insulation. in building materials the highest R factors could be found in vacuum insulated panels (5.28 - 8.8), silica aerogel (1.76) and various polyurethane panels (1.10 - 1.41)
Add your answer:
Earn +20 pts
What is the best type of insulation?
The Best Type Of Insulation is Spray Foam Insulation. Because Spray foam insulation, also known as polyurethane foam insulation, is a superior form of insulation that provides a higher thermal insulating value (also known as R or RSI value) than conventional batt insulation. The application ensures that any gaps are sealed, providing a vapor barrier, moisture barrier, air barrier and even a radon barrier, thus stopping any thermal loss due to drafts or leaks. This makes spray foam up to 50% more energy efficient that other insulation solutions, resulting in cost savings on energy and gas bills. It is important to understand that a lot of the heat or cold air loss happens due to the air leaks on your walls or roofs, and that the cheaper batt insulation installation is quite susceptible to leaks if the vapor barrier (that layer of poly plastic applied just before the drywall) is not properly installed or if it becomes damaged. Further, unlike batt insulation, spray foam barrie insulation does not shift, sag or become wet or moldy. Rather it adds to the structural integrity of the house, with the added benefit of keeping out pests or vermin. For More Details Visit sprayfoammasters.ca
The effectiveness of insulation is rated with?
I want to say either R-Value or Temperature Value? Probably R-Value... Out of answers: a. convection value b. R-value c. temperature value d. solar value
What is the best insulation for the ducts of a central AC system because condensation will build sometimes?
The idea is to insulate to keep air and it's moisture content away from the metal pipes. A double faced insulation with foil on the pipe side is very good. I wrapped mine with r-13 single faced ceiling joist rolls and don't expect to have any condensate problems.
How much insulation R factor do I need in exterior walls for Southeast Georgia sumertime heat Is greenboard and plastic necesary for carboy long term storage and screw cap 1.75 liter bottle storage How important is moisture in those conditions?
Plastic deteriorates in the sun. Good insulation is very important. I suggest going to home depot. They have free classes.
What is the best way to remember the water cycle?
R then C then R i l a s o i e u n d Rocks Can Roll
An R-value is a rating for materials used as?
insulation
What is the proper r-value for insulation for ceilings and exterior walls?
The required R value for walls and roof insulation varies depending on your local building authority. The ideal R value will depend on the climate, altitude, latitude and exposure of your site and the form, amount of glazing,materials and use of the building.
What is the r rating of white styrofoam insulation?
3/4" = R2. Two layers with a 3/4" airgap pumps it up to a R6.
What value does 10 insulation give?
If you are referring to the R value of insulation, then 10 would be the 'thermal resistance' value of the insulation. A value of 10 is about what 3 1/2 inches of fiberglass batt insulation would give you. That is what you might put within your exterior walls if you are using wood studs. The higher the R value the better insulation you will have. When you add up all of the R values of the materials that make up your exterior wall you will get your total value. Depending on where your building is located, and the climate in that area, you will need to adjust your insulation accordingly.
Which takes in more heat r-5 insulation or r-35 insulation?
n0
What is the best type of attic insulation?
Insulation is rated in terms of thermal resistance, called R-value, which indicates the resistance to heat flow. The higher the R-value, the greater the insulating effectiveness. The R-value of thermal insulation depends on the type of material, its thickness, and its density. In calculating the R-value of a multi-layered installation, the R-values of the individual layers are added.
What is the 'R' value of garage door insulation?
The R-value is a valuation of how well-insulated the garage door is. The higher the R-value, the better insulated it is, but when comparing it is wise to learn if the given rating is based on the entire door or only certain portions.
How is insulation measured?
Floors, attics and walls all require insulation of different R-Values which are measured by the thickness of the insulation. The R-Value determines how well the insulation will resist heat flow. The higher the R-Value the more resistance it has to heat and cold. If you are adding to existing insulation there is another factor to consider. You will have to determine the R-Value of the existing to know how much additional insulation to add
What are value of insulation should you have in AZ?
in arizona according to the Department of Energy, they call for in an attic insulated home to have the equivalent of 16 inches to 18 inches of blown in attic insulation. Attic insulation is measured in R values regardless of what type of insulation you blow in or lay down. Attic guard is usually your best type of insulation which should be blown in at an R value of 49-60 in an Arizona home
Is r-value good or bad?
it is a good thing i think R Value is the thermal resistance of a given material. The higher the R Value the more thermal resistance and the better the insulation. So, an R48 roof system is warmer than an R32 roof system. All insulation materials are rated by their R Value. An inch of rigid insulation has a higher R Value than an inch of fiberglass insulation. Check with the insulation manufacturer for the R Value.
Which absorbs more heat R-5 insulation or R-35 insulation?
Either - the R number refers to the ability to block heat transfer, not absorb it.
Insulation for roof's?
R-38
