answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered
2014-06-25 18:25:38
2014-06-25 18:25:38

OEM are the best spark plug wires for the Honda cbr. These spark plug wires can be found at the local Honda dealership.

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


spark plug wire setup spark plug wire setup



The spark plugs in a Honda VTX 1300 can be removed by first removing the spark plug wire. Twist the spark plug out, using a spark plug socket. Reverse the process to install the new spark plug.


By taking the spark plug wire off, and then using a spark plug socket with a ratchet and extension. It's not rocket science.



What is the proper spark plug wire placement routing to the distributor for a 1994 Honda civic cx


Spark plug wire not connected to spark plug? Spark plug wire connected to Wrong spark plug? Vacuum line disconnected? Bad spark plug or wire?


you might want to check your coil or your plug wire


If you mean that the wire came out of the boot, then pull the boot off of the spark plug and use a spark plug socket to remove the spark plug.


Depends on what we are talking about. There is the Honda Recon 250 ATV with a single cylindar engine, the spark plug is located at the cylinder head. The Honda Hornet motorcycle is a 4 cylindar bike with the spark plugs at the side of the cylinder heads. Then there is the single cylindar Honda Nighthawk 250 one cylindar motorcycle with the spark plug located at the side of the cylinder hear. The spark plug is easily located on any vehicle as it is visible by a thick wire and a (usually) rubber spark plug cap.


there are four spark plug wires that run to the distributor..the fifth one is the coil wire


The best way is to use the spark plug socket out of the factory tool kit. If you do not have that use a normal 5/8" socket to loosen the spark plug. Use the spark plug wire to snap back on after the plug is loose and pull it out. The spark plug is at the very top of the engine, the spark plug wire is a real good indicator of its location.


The first thing to do if one cylinder is not firing on a 1989 Honda Civic SI, is to disconnect the battery. Then remove the spark plug wire and the spark plug. Check to see that there is no oil on the plug and it has the right gap measurement. Then replace the spark plug and wire and try the engine again. If it is still misfiring, change the spark plug. If that does not fix the problem, have a compression check done for that cylinder.


http://henklin.ridethepig.com/Civic/firing_order/


Changing the spark plug wires in your 1999 Mercedes-Benz is quite simple. The spark plug wires simply lift off. The new spark plug wires can be pushed onto the spark plug. It is best to change one wire at a time.


The rubber end on the spark plug wire.


Spark Plug Wires? Remove them 1 at a time from the spark plug to the distributor or the ION pack, remove and replace the spark plug, add the new spark plug wire from the newly added spark plug to the distributor or ION pack.


no it can not start with a broken spark plug wire unless you fix it


Remove the spark plug wire from the spark plug. Use some heavy gloves or a set of insulated pliers to hold the spark plug wire about 1/4-inch from the engine block (ground) and crank the engine - you should see a spark jump from the wire to the engine ground. For a better check, use another spark plug and put it on the spark plug wire and use it as a "jumper" from the wire to the engine ground.


Defective spark plug? Defective plug wire?


You can check for spark by removing the plug wire from the spark plug and holding it about 1/4 inch from ground. Have some one crank the engine or pull the starter rope and look for a spark to jump from the spark plug wire to ground. DO NOT hold the wire with your bare hands since you will get shocked. If you have spark there, remove the spark plug and insert it into the end of the spark plug wire and do the same procedure. If there is no spark, the plug is bad. If you have spark, the problem lies elsewhwere.


Used proper sized spark plug socket with long extention and ratchet. Disconnect spark plug wire by using wire puller or tugging at boot of wire. Place spark plug socket over spark plug securely and removed.


If your Honda CRV cranks but won't turn over because the spark plugs are not getting spark, ensure the wires are connected. A loose spark plug wire can cause this issue.


It is important to know how the engine of a car works. In a car, the spark plug cables connect to the vehicles spark plugs.


first did you chech for spark by removing the spark plug and then attach the plug wire back on it and touch the other end on something metal while you are startin the bike and you will be able to see if you have spark



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.