Chevy Malibu

What is the cable used for on the rear window assembly of a 2000 Chevy Malibu?

123

Top Answer
User Avatar
Wiki User
Answered
2008-08-12 12:08:22
2008-08-12 12:08:22

Probably for the rear window defroster

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


It is located underneath the throttle cable assembly, behind the exhaust manifold. It is no shade tree mechanic job to replace this.

If the window is stuck in the down position on a Chevy Silverado, the door panel will have to come off to access the cable mechanism and fix the window. If the windows are electric, there will also be the wiring assembly for the window to remove.

You will have to replace the complete window regulator assembly.

To fix a cable on an electric window on a 2004 Chevy Epica you need to first gain access to the wire by removing the door panel. From there, you can either fix or replace the cable.

kick down cable is out of adjustment from pedal to transmission.

Begin by removing the decorative radio cover in your 2006 Chevy Malibu. Remove the radio retaining screws. Remove the wiring harness and the antenna cable from the back of the radio.

Remove the retaining cover to your 2005 Chevy Malibu radio. Remove the radio retaining screws. Slide the radio out. Remove the wiring harness and the antenna cable.

how do u disconnect the cable from the back how do you remove the ignition switch from a 2001 Chevy Malibu you have to put the old key in the ignition. then if you feel around on the bottom of the assembly you will find a small almost rectangular button. depress this and then proceed to turn the ignition clockwise. this will move it to the right position and if everything works correctly it will just slide out.

Remove the positive battery cable from your 2000 Chevy Malibu battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.

The latch assembly and cable is one piece.

Remove the old battery, disconnect the negative cable first and install the new battery connect the negative cable last.

You will have to remove the door panel and replace the regulator assembly. In some cases it comes as an assembly with the motor.

The power window assembly for the 2000 Buick is an electric motor connected to a cable and capstan that raises and lowers the window via linkages for lack of a better term. From experience the motor doesn't usually go bad, it is the window cable capstan wears because it's plastic and the cable is steel. If you're handy you can get the assembly from the web and replace it for $50-$60. If not take it in and have the pros do it.

You have a broken cable in the window regulator. You will need a new window regulator assembly.

The cable runs through and is coiled inside the motor. It is advised to replace as an assembly.

Tale the window regulator out of the truck. Clean an lubricate the tracks & guides. Check for a frayed cable.

You must replace the entire regulator.Here's howhttp://www.ricksfreeautorepairadvice.com/repair-topics/window-power-repair/replace-a-power-window-regulator

check shift cable to transmission,it is either broke or stretched out !!!!

You will have to get a window regulator plastic cable to repair. Will have to remove window regulator motor assembly from door. Plastic cable is usually found in the help section of Autozone store. Can also be gotten at other parts stores also.

The 1999 Chevrolet Malibu automatic transmission shift cable has adjustment nuts on each end of the cable. Turning the adjustment nuts will lengthen or shorten the shifting cable.

It does not use a cable. The heater blend door is operated by a electric motor. The complete dash assembly needs to be removed to gain access to the unit.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.