0
What is the difference between fiber shelkote and polyester gelcoat?
Wiki User
∙ 11y ago
Fibre-shelkote distributes vinyl ester resin which is required for underwater usage. Polyester resin is chemically similar to 2 part epoxy, and is much less expensive,
but should never be used underwater.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
You are working on a power boat repaired fiberglass bottom primered it with a urethane primer wanted to know how to prep primer for jellcoat paint procedure?
Urethane primers are not not compatible with gelcoat, nor are epoxy primers. Gelcoat can only be applied to bare fibreglass, existing (well sanded) gelcoat or polyester/vinylester based fillers.
Can gelcoat be thined?
Gelcoat can be thinned using special spray gun that is available in the market.
How do you refinish a fiberglass canoe?
The best way is to sand down the gelcoat finish back to the fibre glass. Mix up new gelcoat and spread over the fibreglass. You need to smooth off the gelcoat as even as possible to eliminate the need to sand down too much. If there are small patches left these can be filled in with a gelcoat mix and sanded down using wet and dry sandpaper.
How do you gelcoat fiberglass?
Gelcoating fiberglass is a critical step in the process of creating a smooth, durable, and aesthetically pleasing surface on fiberglass-reinforced objects, such as boats, automotive parts, and fiberglass pools. Gelcoat is a type of resin specifically formulated to provide a glossy, protective finish to fiberglass surfaces. Here's a step-by-step guide on how to gelcoat fiberglass: Surface Preparation: Begin by thoroughly cleaning the fiberglass surface to remove any dirt, grease, wax, or other contaminants. Use a solvent-based cleaner or detergent and water, followed by rinsing and drying the surface completely. Sand the surface with fine-grit sandpaper (typically 320 to 400 grit) to create a rough texture for better adhesion of the gelcoat. Ensure to sand evenly and remove any gloss from the surface. Wipe down the sanded surface with a tack cloth to remove any dust particles or residues. Mixing Gelcoat: Wear appropriate personal protective equipment (PPE), including gloves and goggles, when handling gelcoat. Follow the manufacturer's instructions for mixing the gelcoat resin and catalyst (hardener) in the correct ratio. Typically, the ratio is specified as a percentage by weight or volume. Mix the gelcoat and catalyst thoroughly in a clean container using a stir stick or mechanical mixer. Ensure complete homogeneity of the mixture to achieve consistent curing. Application: Apply the mixed gelcoat to the prepared fiberglass surface using a spray gun, brush, or roller, depending on the size and complexity of the object. Work quickly but methodically to ensure even coverage and minimize the risk of streaks, drips, or bubbles. Apply multiple thin coats rather than a single thick coat for better control and to avoid sagging or running of the gelcoat. Pay attention to overlapping each pass slightly to achieve uniform coverage and thickness. Curing: Allow the gelcoat to cure according to the manufacturer's recommendations. Curing times can vary depending on factors such as temperature, humidity, and the type of catalyst used. Ensure the curing environment is free from dust, debris, and other contaminants that could mar the surface. Monitor the gelcoat during the curing process to ensure proper adhesion and the absence of any defects. Finishing: After the gelcoat has fully cured, inspect the surface for any imperfections such as air bubbles, pinholes, or unevenness. Sand the cured gelcoat surface lightly with fine-grit sandpaper (typically 600 to 1500 grit) to remove any imperfections and achieve a smooth finish. Polish the sanded surface using a compound and polishing pad to restore gloss and enhance the appearance of the gelcoat. By following these steps carefully and adhering to proper techniques and safety precautions, you can achieve a high-quality gelcoat finish on fiberglass surfaces, ensuring durability, protection, and aesthetic appeal.
What kind of paint do you use to paint a fiberglass pool and do you need a primer?
You should use exactly the same "pool paint" used originally, when the pool was manufactured. It's called gelcoat and can only be purchased online. Until 1999, fiberglass pool owners were forced to use epoxy, which lasts only a few years before chaulking, peeling, and cracking. Now there's a product called fibre-shelkote which is exactly the same formulation that lasted more than 20 years after your pool was built. But you'll need to call a sandblasting contractor to remove the old gelcoat before you can roll-on the new stuff. Hum, are you certain that your pool needs to be painted. Has it been painted before. How old is the pool? Maybe it just needs to be drained and cleaned. You need to be certain that has been painted in the first place.
Do you need to use a primer with polyurethane paint on fiberglass?
On raw fibreglass, epoxy primer is necessary. On gelcoat, polyurathane paint sticks well, provided the surface is well sanded and cleaned with acetone, but pinholes and cratering can be a problem, so where a high standard is required, priming the gelcoat with epoxy is recommended.
Can car wax be used to wax a boat?
Yes, car wax is also suitible for gelcoat or urathane paint on boats.
How do you remove rust stains from fiberglass boats?
Try using CLR, but don't leave it on the gelcoat for too long as it will dull the surface. Otherwise, cut it back with 1200 grit wet & dry and buff it with compound. After cleaning and removing the rust ... use Zirlon clear top coat .. it will stop the rust and put the gloss back onto the gelcoat. It is an all green product that will last 3 to 5 yrs.
Can the resin wall of an in ground pool be patched successfully if it has a hole the size of a hockey puck in it?
If you are referring to a fiberglass wall manufactured from fiberglass, resin, and gelcoat, the answer is absolutely. Best of all, the repair is really inexpensive.
Can you paint a fiberglass motorhome panels?
Yes. If you want a good finish that will last, the gelcoat must be well sanded with 240 grit paper, primed with an epoxy undercoat and topcoated in 2-pack urathane gloss.
What are the advantages and disadvantages of a fiberglass swimming pool lining in a gunite pool?
There are no disadvantages if the pool is properly prepared and, most importantly, the right materials are used to create the fiberglass shell. It is up to the consumer to demand the specific resin, fiberglass mat weight, and gelcoat that will be used in the application. When the materials are delivered, no matter who delivers it, the consumer must demand the Material Data Safety Sheets MSDS, and verify that they represent the exact materials ordered. Then the MSDS must be compared to the Chemical Manufacturers labels before the shipment is accepted. Once you accept it, you're stuck. Assuming the right (which happen to be the most expensive) chemicals and fiberglass are used, and the gelcoat is applied in a timely fashion, (to achieve a chemical bond), the pool will not leak for at least 30 years. The maintenance and chemical usage will be reduced by more than 50%, and the pool will look new and beautiful once again. Between 12 and 18 years later, depending upon pool use and care, the pool will need to be re-gelcoated. Salt water chlorination increases the longevity of the original gelcoat toward the upper end of the term.
Can you colour carbon fiber?
You can, although you aren't polishing the carbon fabric itself. Instead, you are polishing the gelcoat, paint, or epoxy matrix that's visible over the carbon fibers. Sanding or polishing through this topcoat can damage the fabric.
