Want this question answered?
a megger or hipot test involves raising the voltage of the wiring to 2x the operating voltage + 1000v answer volts/amps or ohms Dielectric test usually a sample of the oil is taken from the transformer answer is in ohm-cm dry devices will have the dielectric tests on file ... this is a very poor excuse ... the code need rewriting. the old standards were based on porcelain, oil, paper and cotton AI MI SWC DWC new types THN THWN THHN SO are generally based on a natural color when the tests are done so if you replace a cord on a drill the white and green wire has insulation that crumbles while the black is still flexable. thermoplastic insulation used for several years in damp locations with DC turns to a sticky goo.
It depends on a lot of factors. Generally speaking, if the insulation is THHN then the rating is 350 amps. If the insulation is THWN then the rating is 310 amps. The ampere rating for wire depends on the temperature of the environment it will be used in, the insulation rating and the number of circuits installed in a conduit. There are also other factors to consider... like voltage drop in long runs.
Wire size is based on the amperage that the load requires. For an accurate answer the motor amperage is needed. That said you can get an approximate figure by this method. 1 HP = 746 watts. This formula for amperage when HP is known. HP x 746/1.73 x Voltage x %Eff x pf. Use a Efficiency % at 90 and a power factor of .85. A horse power of 5 x 746 = 3730/1.73 x 220 x 90% x .85 = 12.81 amps. Code states that motor supply conductors have to be 125% of the full load amps = 16 amps. Code also states that conductors can only be loaded to 80% on continuous load which a motor falls into. A #12 copper wire 90 degree insulation is rated at 20 amps x 80% = 16 amps. A #12 wire will do the job. It will need a 40 amp three pole breaker, 50 amp non time delay fuse or a 30 amp time delay fuse to feed the motor.
Cross link polyvinyl chloride RW90 (PVC) and THHN are two common types of insulation THHN wire stands for thermoplastic high heat resistant nylon coated wire. THWN stands for thermoplastic heat- and moisture resistant nylon coated wire.
No. Per the National Electrical Code, table 310.13, THWN is suitable for dry and wet locations with a maximum operating temperature of 75o C. THWN-2 wire is suitable for dry and wet locations up to 90o C.
a megger or hipot test involves raising the voltage of the wiring to 2x the operating voltage + 1000v answer volts/amps or ohms Dielectric test usually a sample of the oil is taken from the transformer answer is in ohm-cm dry devices will have the dielectric tests on file ... this is a very poor excuse ... the code need rewriting. the old standards were based on porcelain, oil, paper and cotton AI MI SWC DWC new types THN THWN THHN SO are generally based on a natural color when the tests are done so if you replace a cord on a drill the white and green wire has insulation that crumbles while the black is still flexable. thermoplastic insulation used for several years in damp locations with DC turns to a sticky goo.
11
A #8 copper conductor with an insulation factor of 60 degrees C is rated at 40 amps, insulation factor of 75 or 90 degrees C is rated at 45 amps.If the breakers rating is 90 degrees C then the amperage can be boosted for 60 degree wire to 40 amps, 75 degree C wire to 50 amps and 90 degree C wire to55 amps.
If it is connected to the internet thwn it can get the time from the internet time service.
Scientists.
I think you mean 16 AWG THWN. It's coating for PVC piping.
1 1/2 inch
This is per the NEC Handbook, 2005 edition. Your municipality may use different rules. I am not an electrician. Per Table 5, chapter 9: Approximate area of 14 ga. THWN is 0.0097 sq. in. Approximate area of 6 ga. THWN is 0.0507 sq. in. 0.0097 * 3 = 0.0291 0.0507 * 4 = 0.2028 ...total area 0.2319 sq. in. Per table 1 chapter 9, you are allowed 40% fill for more than two wires in EMT. So, 0.2319 / 0.4 = 5.7975 sq. in. minimum conduit area, which means you'd have to use 2-1/2 inch trade size EMT, which is 5.858 sq. in. Hope this helps.
First find out how much concrete is needed for your project thwn do the calculations.
You have to make sure none of his friends are around then you have to tell if he hangs out with you alot, if he does then he probally likes you. Then wwhen he lokks into your eyes you can say I love you. if he says,"what?!?!?!?" thwn say,"I was just joking"