hfghfgh
differences between unilateral and bilateral networks
None, if you meant "contract".
you will need to be sensitive to the differences between you and to identify those differences that have the potential to become barriers to your interactions. Accommodating these differences means building trust and respect, which can only be achieved by open and honest communication between you
tcp/ip is good....
what is the difference between Interpersonal and Business Communication?
We can use I2C only for small distance communication not more than 1 meter, but CAN bus can be used for more than this distance that's why in todays world CAN bus is most preferred in Automotive Industry.
Major difference between Bus and Register is that B for Bus while R for Register
there is no dif
Major Difference Between SPI and I2C is: SPI is full Duplex (SPI can be full/half duplex, depending on the hardware, 3 or 4 wire) and I2C is half duplex communication....we cannt send and receive data at a time in I2c..but it possible in SPI ....SPI much faster Than I2C....... Main topic to discuss the difference is 1) speed is difference in case of i2c is 100/400kbps in 7 bit mode max 400kbps (But High speed I2C communication protocols allow speeds upto 3.4Mbps!!) in case of spi speed is upto 1mbps (the higher speed of SPI is due to fact that unlike I2C, SPI interfaces to a slave device using a sperate pin called the slave select + no concept of acknowledgements which means increased Band width..) 2)Connection wise: i2c require less pin then spi (SPI 3wire: 3 IOs, SPI 4 wire: 4 IOs, I2C: 2 IOs) as spi require slave select for individual device... 3)it is better to use i2c in case of if u want to connect more device to connect. (slave addressing advantageous over SPI slave select individual pins for individual slaves) 4)bus arbitration is possible in case of i2c... not in case of spi... (SPI does not require it, since only 1 slave is controlled by the master at any given point) 6)noise sensitivity of i2c is high... there is chance to corrupt the r/w bit... then whole data is corrputed... but in case of spi.. chance is very less as whole word is trasmitted... However, I must say that I2C is more reliable, since the protocol supports slave feedback machanism (ACK) to detect whether was received correctly or corrupt. 8) it is easy to implement the spi...while i2c is little bit complex... (over heads) Formatted Answer @: http://www.bubblews.com/account/65122-kapilddit
In terms of power I2C stands for an "Inter-Integrated Circuit". An I2C is used to connect slow speed computer components to the motherboard or other electronic devices.
the difference between driving a bus as compared to a car is with a bus you need to make wider turns and with a car you can just go for the turn
I2C (Inter-Integrated Circuit) is a serial communication protocol that uses two wire lines for communication, allowing multiple devices to be connected in a network. RS232 (Recommended Standard 232) is a serial communication standard that uses a single wire for data transfer and is commonly used for connecting devices like modems, printers, and GPS receivers. Additionally, RS232 uses voltage levels for signaling while I2C uses open-drain signals.
That varies greatly based on a number of factors. There'll be significant differences between mileage when you compare a school bus driver, metro bus driver, shuttle bus driver, coach bus driver, and anyone driving any other type of bus. It could be as little as a few miles each day, or upwards of 500 miles.
they look stylish and it is faster and convenient to travel the early buses is not too much convenient to travel and also not too stylish
Mainly, yes, but there are minor differences, and of cource the bus engine is usually largest :)
Two roles of nodes in I2C communication are: master and slave.Master node - node that generates the clock and initiates communication with slavesSlave node - node that receives the clock and responds when addressed by the master
Its the seats that make the difference between a coach and a bus.