answersLogoWhite
Timing and Firing Orders
Chevy S-10
Ford F-150

What is the firing order for a 1990 Chevy S-10 2.5L?

141516

Top Answer
User Avatar
Wiki User
Answered 2006-02-23 20:57:24

For a 1990 Chevy S10 2.5L engine the firing order is: 1-3-4-2 . The distributor rotates clockwise.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


just type "25l to ml" in google. You can do this for almost any conversion.


I have the EGR disabled on my 1990 truck, 5.7. If i can disable it on my truck without a problem, i cant see why a car wouldn't work, as the engine would be working less. 2 mpg increase in fuel economy. Apparently higher combustion chamber temps.


By the way, it's a 2.5 Liter engine, the system saved it as a 25L for whatever reason.


25 litres of what? Depending on the density of the material, the answer varies. 25l of sand will weigh a whole lot more that 25l of feathers. If you mean water, 1l of water weighs 1kg, so 25l of water weighs 25kg. That is water at (I think) 20C at sea level. Hope this answers your question.



25 litres is 110.231 cups


25/1.5=16.67 times approx.


25L is about 105.7 cups.


2500cL = 25L* There are 100cL per liter


I wish I could answer you but I am having the same problem with my 89 Chevy s10 everything was fine till working on distributor. put new computer in still not help have fuel pressure. If you fixed your problem maybe you could give me some info?


Not much; they are a sled. Sorry, but I had one. Mark


A quart is two pints, a US pint is different from a UK pint. A us pint is 473ml,a UK pint 568ml. this is why metric is better, it's the same everywhere. 25l is 26.417 quarts US 25l is 21.997 quarts UK.


Gold has a specific gravity of almost 20. If a 25-liter pack of water weighs 25 kilograms, how much would a 25-liter pail of gold weigh?




4 Runways which you can land both ways - so 8 in total... 6L/24R 6R/24L 7L/25R 7R/25L


Taking 1 inch to be about 2.5cm, an inch of rain on an area of 1m2 is approximatley 0.025m3, or 25000cm3. That is 25000ml or 25l of water.


http://www.carquest.com/techbulletins/brakes/2001/CQB%2001-10.pdf


You'll want to find out the density of cat litter to get the actual measurement, but they're roughly the same amount (based on water conversion)


depends on the size of the bike...... my yz 250f holds about 25l when full.... bigger bikes hold more and visaversa for smaller bikes..


it is directly below the intake manifold on the engine block. i do believe it is the only 1/2 inch hose connected to the intake plenum.


It's right on the throttle body, just to the left of the center of the motor (top of motor, easy to see) Regards


Clutch pedal lever. SWITCH IS AT THE TOP OF CLUTCH PEDDLE BUT THE OVER RIDE FUSE IS # 20 ON FUSE PANEL REPLACING THE FUSE WILL DISCONECT SWITCH.


It is my understanding that there were actually four different blocks that were all used for the 2.5L engine. The blocks used for the FWD engines are not the same as the block used with the rear wheel drive vehicles such as the S10. Differences include motor mount holes and starter locations. For the final answer put the two blocks side by side and make sure all the critical mount positions line up. If they do you can probably interchange them.


If you are refering to the cv boots on the half shafts I have found that not only is it almost cheaper but easier just to replace the entire shafts on each side. They come as an entire assembly which makes replacement fairly easy. I am speaking from experience. These cars are a money pit and I'd recommend dumping it. I'd love to dump mine but I've got so much money in repairs into it now that I'll have to drive it until dooms day.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.