0
Unbalance in three phase system puts quite a negative impact on the system and the three phase loads like motor. Motors tend to draw additional current for same power output, may increase noice, may increase heat generation.Over all losses go up in the system
Wiki User
∙ 6y ago
Add your answer:
Earn +20 pts
How does a phase leg connect to a neutral in an electrical circuit?
A phase leg connects to the neutral through the connected load.
What is a short load system?
Electrical load forecasting. "A good electrical load forecast has a direct and significant impact on costly generating unit startups and shutdowns, energy purchases, managing system demand as well as scheduling system upgrades based on predicted load growth."
What is mean by balanced and unbalanced load?
There is a lot of confusion amongst consumers that an Unbalanced LoadStabilizer is generally superior to a Balanced Load Stabilizer. To clarifythis myth certain fundamental principles connected with Transformersare given below:1. Definition of Balanced and Unbalanced loads:a. A Three phase Loads on a 3 phase supply system is a Balancedload because it draws equal current from each phase. Three phaseMotors, Converters; Rectifiers using 3 phase input supply arecommon examples of Balanced loads.b. A single phase / 2 phase loads on a three phase system is calledUnbalanced load. Normally Unbalanced loads have to use aneutral wire in the system. The 2 phase loads may not require aneutral.
Is 10 kva supply to 3 phase load is equal to 10kva supply to single phase load?
Yes of course!! 10 kva electrical power is 10 kva electrical power either it would be three phase or single phase. But other factors i.e. current, voltage changes accordingly. Actually this question is quit confusable. Because in 3phase system, if each phase gives 10kva power (single phase power = 10 kva) then 3 phase power will be 10 X 3 = 30 Kva If we go leteratualy towasrds the question, then the asnwer will be - No. becasue 10 kva supply to 3 phase load will be 3phase supply(i.e440V) & 10kva supply to single phase load will be single supply (i.e 250V).
Is it possible to synchronise two generators with no common electrical load to be exactly out of phase?
No, is it not permissible to synchronise two generators with no common electrical load to be exactly out of phase. Doing so would represent a double short circuit to both generators, and possible destruction of both generators. Whether it is possible or not depends on the design of the synchronizing circuit and/or the stupidity of the operator.
How does a phase leg connect to a neutral in an electrical circuit?
A phase leg connects to the neutral through the connected load.
What will happen if 2 phase load is connected to generator?
There is no such thing as a two phase load any more. Any two legs from a three phase system are classed as single phase. If this single phase load is connected across the generator it will induce an imbalance in the output voltages of the generator. This is one reason that single phase loads on a three phase generator should be shifted around to find the best possible balance.
Line read 20 amp different per phase to load?
The electrical term for this condition is called an unbalanced load.
Should all three phases of 3 phase motor are to be equal on no-load and load conditions?
Ideally all three phase currents will be equal. There may exist some voltage imbalance from the power source, which will result in unequal currents.
What is a short load system?
Electrical load forecasting. "A good electrical load forecast has a direct and significant impact on costly generating unit startups and shutdowns, energy purchases, managing system demand as well as scheduling system upgrades based on predicted load growth."
What is mean by balanced and unbalanced load?
There is a lot of confusion amongst consumers that an Unbalanced LoadStabilizer is generally superior to a Balanced Load Stabilizer. To clarifythis myth certain fundamental principles connected with Transformersare given below:1. Definition of Balanced and Unbalanced loads:a. A Three phase Loads on a 3 phase supply system is a Balancedload because it draws equal current from each phase. Three phaseMotors, Converters; Rectifiers using 3 phase input supply arecommon examples of Balanced loads.b. A single phase / 2 phase loads on a three phase system is calledUnbalanced load. Normally Unbalanced loads have to use aneutral wire in the system. The 2 phase loads may not require aneutral.
How many feeder you can use for chiller?
One feeder will do the job. The definition of a feeder in the electrical trade is a set of conductors that supply a source to a load. The sizing of the feeders will depend on what the load current is. The wire count of the feeder will be dependant upon whether the load is single phase or three phase.
Is 10 kva supply to 3 phase load is equal to 10kva supply to single phase load?
Yes of course!! 10 kva electrical power is 10 kva electrical power either it would be three phase or single phase. But other factors i.e. current, voltage changes accordingly. Actually this question is quit confusable. Because in 3phase system, if each phase gives 10kva power (single phase power = 10 kva) then 3 phase power will be 10 X 3 = 30 Kva If we go leteratualy towasrds the question, then the asnwer will be - No. becasue 10 kva supply to 3 phase load will be 3phase supply(i.e440V) & 10kva supply to single phase load will be single supply (i.e 250V).
What is a real life application of the square root function?
Electrical engineers use it in calculating power factor and electrical load distribution when dealing with 3 phase power connections.
What happened when one phase missing of a 3 phase load?
If one phase really is missing, then you have an unbalanced load.
What are the uses of single phase or three phase motor?
torque load, generation load, power correction load
Is it possible to synchronise two generators with no common electrical load to be exactly out of phase?
No, is it not permissible to synchronise two generators with no common electrical load to be exactly out of phase. Doing so would represent a double short circuit to both generators, and possible destruction of both generators. Whether it is possible or not depends on the design of the synchronizing circuit and/or the stupidity of the operator.
