0
What else can I help you with?
What is a h 10 load rating?
what is H-10 wheel loading
What is meant by pressure rating of pump?
Pressure rating means maximum pressure at which pump can operate safely.Pump delivers a pressure according to load. If load is more , it'll deliver more pressure. At some point load is large enough to cause damage to parts of the pump. That pressure is rated pressure. For example if pump rating is 10 bar, it can asustain safely the load that creates 10 bar pressure.
What does the 5.9L Cummins engine get for mpg?
Depends on the horsepower rating, load, and gear ratio of the axles. Could be anywhere from 10 to 25 mpg.
What the different between c10 and c20 rating of battery?
The c rating is known as the coloumb rating and indicates the rate of discharge that is recommended. A c10 will last for 10 hours with a 15 amp load, and a c20 will last for 20 hours on a 7.5 amp load. Ideally, the c10 is used in situations where you will have more charge/discharge cycles on the battery and a c20 is for high charge and discharge rates.
How do you calculate battery amp hours?
C/20 is the formula most commonly used to describe a battery according to its amp hour rating; for instance a 400Ahr rated battery means that a 20 amp load placed upon the battery delivers at that rate of energy for 20 hours upon reaching the manufacturer's per cell rating, usually about 1.7 volts or 10 volts for a dead, discharged battery. There are different discharge or load ratings such as a 10 hour or 100 hour rating resulting in a different Amp Hour rating for the very same battery. A battery is an electrical potential energy source whose capacity (amount of energy density delivered over time) is determined by the rate/time over which the battery will deliver a set rate of load/discharge. The lesser the load, the longer the rate, the higher the load the shorter the rate.
What were conditions like for slaves?
it was hard for them they had to sleep and go to the toilet were they were sitting they were beaten and estimated 10% died on there journey they would have to sleep naked on hard wooden floor
What wire size for 3 phase 460 volt 30 amps?
A breaker is sized by the load current. A breaker is used to protect the load feeder from an over current being applied to the conductor. If the load draws up to 30 amps, the wire size needs to be a #10 copper conductor or larger depending on the distance to the load with an insulation rating of 90 degrees C. The 460 volt source has to do with the insulation rating of the conductor. In this case the #10 conductor will need an insulation rating of 600 volts. Do not use 300 volt rated wire.
Can you replace a 15 amp fuse with a 10 amp fuse?
not smart to do it cant carry the load of the circuit it will blow. in emergency maybe but never go with a higher rating
When was Shaolin Wooden Men created?
Shaolin Wooden Men was created on 1976-10-10.
What is demand load for a 15kw 14kw 9kw and 10kw ranges?
Demand load refers to the maximum amount of power that electrical equipment or systems require at any given time. For ranges with ratings of 15 kW, 14 kW, 10 kW, and 9 kW, the demand load would typically be the highest wattage rating during peak operation. However, in practice, demand load calculations often consider factors like diversity and load factors, which can reduce the effective demand load from the maximum rating. Thus, the actual demand load may be lower than the rated wattage depending on usage patterns.
What is the maximum amp rating for a device that is designed to handle a 10-2 amp rating?
The maximum amp rating for a device designed to handle a 10-2 amp rating is 10 amps.
What does 10VA mean on a transformer?
The designation "10VA" on a transformer indicates its power rating, specifically that it can handle a maximum load of 10 volt-amperes (VA). This rating combines both the voltage and current capacity, reflecting the transformer's ability to supply power to connected devices. In practical terms, it helps users determine if the transformer is suitable for their specific application or load requirements.
