0
What is the minimum anchorage length on re-bars in concrete cantilever beams?
Wiki User
∙ 14y ago
you can generally use 180 degree hooks, to provide enough anchorage in slabs with no edge beams. use the Ldh formula (12.5.2) of ACI 318-11
Wiki User
∙ 12y ago
Wiki User
∙ 14y agoThis should be the development length
Add your answer:
Earn +20 pts
What is the max length of RC cantilever beams?
1.50 meter from the support is the max. safe length cantilever beam
Is the Quebec Bridge a cantilever bridge?
Yes. The Quebec Bridge, which crosses the lower Saint Lawrence River in Canada, is the largest cantilever bridge in the world. Each cantilever spans 177m, and the total length of the bridge is 987m.
What is lap length of M20 concrete?
my big hole
What is the setting time of concrete?
The length of time that concrete takes to set, will depend on the temperature. It would take approximately 4 hours for concrete to set at a temperature of 80 degrees.
How many bytes are in a binary code?
There is no real answer to this. Binary codes can be any length. The minimum length is 1 byte.
What is the max length of cantilever beam?
1.50 meter from the support is the max. safe length cantilever beam
What is the max length of RC cantilever beams?
1.50 meter from the support is the max. safe length cantilever beam
What is the minimum anchorage length for reinforcement?
It is the length of the main bar provided at the column beam junction or column footing junction to allow for the development of stresses to its design strength.
Is the Quebec Bridge a cantilever bridge?
Yes. The Quebec Bridge, which crosses the lower Saint Lawrence River in Canada, is the largest cantilever bridge in the world. Each cantilever spans 177m, and the total length of the bridge is 987m.
What is the difference between anchorage length and development length?
Anchorage length is the required distance to transfer a load and is dependent on the materials used. Development length is the length of the reinforcement bar or rod required to transfer the load safely to another bar.
When a cantilever is loaded with udl the maximum bending moment occurs at?
When a cantilever beam is loaded with a Uniformly Distributed Load (UDL), the maximum bending moment occurs at the fixed support or the point of fixation. In other words, the point where the cantilever is attached to the wall or the ground experiences the highest bending moment. A cantilever beam is a structural element that is fixed at one end and free at the other end. When a UDL is applied to the free end of the cantilever, the load is distributed uniformly along the length of the beam. As a result, the bending moment gradually increases from zero at the free end to its maximum value at the fixed support. The bending moment at any section along the cantilever can be calculated using the following formula for a UDL: Bending Moment (M) = (UDL × distance from support) × (length of the cantilever - distance from support) At the fixed support, the distance from the support is zero, which means that the bending moment at that point is: Maximum Bending Moment (Mmax) = UDL × length of the cantilever Therefore, the maximum bending moment in a cantilever beam loaded with a UDL occurs at the fixed support. This information is essential for designing and analyzing cantilever structures to ensure they can withstand the applied loads without failure.
How do you find a reaction force at the middleL2 of a cantilever beam length L using deflection method?
I also want to find the similar answer
Minimum width and length of penis?
minimum width is like 10 cm and length is like 20 cm
How do you calculate concrete needed?
length*breadth*depth of the structure=...........m3 of concrete is needed. .
What is the development anchorage length of a beam tension bars?
formula of steel weight per sqm
What is the Formula for development length in concrete?
it c@
What is a cantilever deck?
A cantilever deck is a deck that is suspended by joists that stick out of the structure. The distance the deck sticks out of the structure is one-third the total length of the cantilever beams that enter the structure. Usually these beams are bolted to (or sistered) to the second story floor joists or the roof trusses. Onto these beams are attached the floorboards that make the surface of the deck. And onto those the railings are attached. Hope that helps :-)
