0
Use only AWG # 10 copper.
Wiki User
∙ 11y ago
Wiki User
∙ 11y agoAWG # 10
Add your answer:
Earn +20 pts
Can I you use existing 8 3 wire hooked to a 30amp breaker was hooked to old electric heater to wire a heater that requires 10 2 wire its a 5000watt 240volt heater?
Yes the wire size is larger for that size breaker but will not effect the 30 amp breaker protection of that circuit.
Have 110volt refrigerator on a 30 amp breaker is that right?
Check the MFG for the amps it uses, if it is suppose to be on a regular 20amp line, then replace the breaker with a 20amp breaker. With the 30amp breaker,it will work, but if there is a surge, you could send too much power to the appliance and fry it. Most refrigerators, are just on a regular 120v household outlet. Besides a 30amp breaker must have 10ga wire, if the wire is 12ga,it can not be attached to a 30amp breaker.
What size wire for 28 amps?
Minimum size is 10 gauge with a 30 amp breaker. To be safe I would install an 8 gauge with a 40 amp breaker.
What size wire do you need to run to an air conditioner that has a maximum breaker size of 40 amps and a minimum circuit size of 25.3 amps?
Number 10 thnn copper wire.
When installing a circuit breaker do you size the breaker to correct wire size or the device its controlling?
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
What size wire would you use on a 30amp breaker?
AWG # 10 wire.
Can I you use existing 8 3 wire hooked to a 30amp breaker was hooked to old electric heater to wire a heater that requires 10 2 wire its a 5000watt 240volt heater?
Yes the wire size is larger for that size breaker but will not effect the 30 amp breaker protection of that circuit.
Have 110volt refrigerator on a 30 amp breaker is that right?
Check the MFG for the amps it uses, if it is suppose to be on a regular 20amp line, then replace the breaker with a 20amp breaker. With the 30amp breaker,it will work, but if there is a surge, you could send too much power to the appliance and fry it. Most refrigerators, are just on a regular 120v household outlet. Besides a 30amp breaker must have 10ga wire, if the wire is 12ga,it can not be attached to a 30amp breaker.
What size wire for 28 amps?
Minimum size is 10 gauge with a 30 amp breaker. To be safe I would install an 8 gauge with a 40 amp breaker.
What size wire do you need to run to an air conditioner that has a maximum breaker size of 40 amps and a minimum circuit size of 25.3 amps?
Number 10 thnn copper wire.
How do you know if the AC breaker matches the AC unit starting demand load?
Read the literature for the ac condensing unit, or the tag on the outside of the unit. Minimum circuit ampacity= minimum breaker, wire and fuse size. Maximum circuit ampacity= the maximum size. Your circuit breaker, wire size and disconnect fuses should all be at or between those 2 numbers.
When installing a circuit breaker do you size the breaker to correct wire size or the device its controlling?
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
What size breaker does it take to run a outdoor well?
Normally AWG #10 wire on a 30 amp breaker but it really depends on the size of the pump. The pump manufacture will specify the size wire and size breaker needed.
Can you switch from 15amp to 20amp on a double pole breaker?
The minimum size wire a 20 amp breaker needs to be connected to is a #12 wire. The 15 is probably connected to a #14 right now which is only rated for 15 amps. Remember the breaker is sized to the wires ampacity not the load .
What size wire and breaker do you need for a 5000 watt garage heater?
Look on the heater and see what amps it is pulling. That will determine the wire size and breaker size. It must be on a dedicated circuit. 15 amps = AWG # 14 wire with 15 amp breaker 20 amps = AWG # 12 wire with 20 amp breaker 30 amps = AWG # 10 wire with 30 amp breaker 40 amps = AWG # 8 wire with 40 amp breaker
What size wire to run 100' from panel using a 30amp breaker for a RV?
Assuming you just plan to run outdoors above ground get a 10 AWG cord specified for outdoor use. It will be a stranded conductor rather than solid.
What size wire do you need to wire a 200 am breaker box?
6
