0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Should braze welding be done in flat position?
Flat position welding is when your job is in a horizontal position the easiest and best position to do welding, then you get vertical up position where the trick is to weave your arc in a V formation, vertical down is used on thin material if its possible at an angle of 45 degrees last overhead that is the most difficult the opposite of flat welding where the job is upside down anytime you look directly down on your weld joint, it is a flat weld, flat position weld are not affected by gravity, as opposed to horizontal, vertical, and overhead, all of which the puddle tends to "sag" as you weld
What is downhill welding?
MY question is (WHAT IS DOWNHILL WELDING) The correct term is Down Hand Welding. Most welds in the vertical position are made from bottom to top. Down Hand means welding from the top to bottom. These welds are usually made on thin metal as the heat input is lower, thereby reducing penetration/burn thru.
How are friction welding joints inspected?
I believe that the most effective and common way to inspect a friction weld is by ultrasound.
What are types of welding machines?
2 basic types, Gas shielding, and flux shielding. Gas shielding comes from compressed tanks of inert gas such as argon. these gases are pumped through the welding hose and over the weld pool. The flux type protects the weld by covering it in a layer of slag that prevent it from being contaminated by the surrounding air.
What size welding rod needed two do a root weld?
The size of the welding rod needed to do the root pass should be the same as the root gap, although in practice, the most common root gap is 1/8" so that the size of the rod to do it is also 1/8".
What is the most common type of welding?
miller lincoln electric and hobart
What are the most common sizes of electrodes use in arc welding?
1/16 inch
What are the common Electrodes for welding spring steel?
Basic celetape found in most stores.
Why are arc welding processes considered the most important of the welding practices?
It is most commonly used, due to the fact the materials that can be welded this way are very common, and the equipment is is relatively inexpensive.
Should braze welding be done in flat position?
Flat position welding is when your job is in a horizontal position the easiest and best position to do welding, then you get vertical up position where the trick is to weave your arc in a V formation, vertical down is used on thin material if its possible at an angle of 45 degrees last overhead that is the most difficult the opposite of flat welding where the job is upside down anytime you look directly down on your weld joint, it is a flat weld, flat position weld are not affected by gravity, as opposed to horizontal, vertical, and overhead, all of which the puddle tends to "sag" as you weld
What is the most common type of fetal testing?
Amniocentesis
What is called welding?
It is called aluminum welding. Aluminum can be TIG welded, the most common method, or oxy-fuel welded, or stick welded, or MIG welded.
What is aluminum welding called?
It is called aluminum welding. Aluminum can be TIG welded, the most common method, or oxy-fuel welded, or stick welded, or MIG welded.
What welding position has the highest heat input?
Heat rises so in my experience it is always overhead that has the most heat input.
What is the most commonly shielding gas for GMAW?
Argon is the most common gas used in gas metal arc welding.
What is downhill welding?
MY question is (WHAT IS DOWNHILL WELDING) The correct term is Down Hand Welding. Most welds in the vertical position are made from bottom to top. Down Hand means welding from the top to bottom. These welds are usually made on thin metal as the heat input is lower, thereby reducing penetration/burn thru.
What is the most common animal that dies from laboratory testing?
The most common animals that die from biomedical tests are mice. The second most common animals are rats.
