0
What is the most suitable method of starting a 10hp motor with reduced inrush starting current?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the difference between the inrush current and the fault current?
Magnetizing inrush current has bigger 2nd harmonics compare to short circuit current. the second harmonics content is about >60% of fundamental harmonic. magnetizing inrush current happened when we energised the transformer, and short circuit current happened if there is a short circuit between different alive phase.
What is wye-delta motor control?
It is a type of starter that allows a motor to be started across the line by starting the motor with a reduced inrush current. The motor is started in a wye configuration until it gets up to speed and then a timer drops the wye contactor out a draws the delta configured contactor in. The motor then operates in a delta wired configuration.
What is primary reactor?
This item is normally seen in electrical switch gear (or called "Starter "/ "Motor drive") . This device is to reduce the inrush current during motor starting. Another item "Line reactor" .
Does a transformer draw a lot of current when first connected to a source?
Yes it does as it is an Inductor and an Inductor needs to build up a magnetic field. It is called INRUSH current.
Why is star-delta starting preferred to direct-online starting?
This type of motor starting configuration is used to start large motors. The utility company's policy is to only let a certain three phase motor horsepower loads across the line starting. High horsepower loads draw high current which draws the line voltage down. This causes a small instantaneous brown out to which the utility company gets complaints about. To solve this problem, limit the horsepower load. Starting a delta motor in star configuration reduces the inrush current because the voltage applied to the motor is lower. This technology is rapidly becoming old due to the new type of motor controllers on the market. Replacing the star delta starters is soft start controllers. The inrush current can be controlled so as to not make any voltage drop on the line. These controllers are different from VFD's which are expensive for this type of application. The main function of the soft start is to get the motor on line without any line disturbances.
Magnetic inrush current in power transformer with waveforms?
The mgnetic inrush current is the current drawn by the transformer when power is applied to the primary winding
Magnetic inrush current in power transformer?
When a transformer is initially connected to a source of AC voltage, there may be a substantial surge of current through the primary winding called inrush current. Inrush current can be up to ten times higher than the continuously needed current because there is low initial resistance.
What is the difference between the inrush current and the fault current?
Magnetizing inrush current has bigger 2nd harmonics compare to short circuit current. the second harmonics content is about >60% of fundamental harmonic. magnetizing inrush current happened when we energised the transformer, and short circuit current happened if there is a short circuit between different alive phase.
What is the inrush current for halogen?
the answer ur looking for is incandescent
How do you calculate fuse rating?
First of all you need to observe maximum current at various possible supply condition (i. e. 220VAC to 260VAC). Then check the inrush current for the equipment. When you start an high power device then it draws 4 times more current than usual. Your fuse should also take care of inrush current. For example: if maximum possible current is 500mA then your inrush current may go upto 2A. Thus if you put a fuse of 600mA then everytime you turn on the device, it may burn the fuse. So the suitable fuse for such condition is 2A
What does LRA stand for on compressors?
LRA stands for Lock Rotor Ampere on compressor and means that it is a high inrush current during starting period of the compressor. Ercona...
How inrush current limited in ups?
Omg girlz sign in the gorop
Will it damage a 3 phase motor to start while spinning down?
No, restarting a motor when it is spooling down will just lower the inrush starting current when the power is re applied.
What are the advantages of using star connection?
The inrush current is reduced. This is the reason for star delta starters. Motor starts on star and after about 10 to 15 seconds, depending on the load of the motor, it switches to a delta configuration to run.
What is wye-delta motor control?
It is a type of starter that allows a motor to be started across the line by starting the motor with a reduced inrush current. The motor is started in a wye configuration until it gets up to speed and then a timer drops the wye contactor out a draws the delta configured contactor in. The motor then operates in a delta wired configuration.
What is Direct online Starter and its disadvantage?
Across the line starter has a large inrush current.
What is primary reactor?
This item is normally seen in electrical switch gear (or called "Starter "/ "Motor drive") . This device is to reduce the inrush current during motor starting. Another item "Line reactor" .
