0
What else can I help you with?
What size wrench is needed to remove the caliper bolts on the front brakes of a 1990 Plymouth Acclaim?
I'm pretty sure that takes a 7mm Allen key.
How do you change wheel bearings on a 1991 Plymouth Acclaim?
Remove the center bolt for the C/V joint... remove rotor and brake caliper, there is 4 bolts that holds it on, remove the bolts and it will come off and install in reverse order. ============================================================== This isn't true for say, a 1989 Acclaim which has the front wheel bearings pressed it, as well as held in by 3 bolts into the spindle. This I know as Ive replaced both my front hub (wheel bearing) assemblies on my 89 Acclaim LX. ~Technologic80
How do you remove the fuel tank from a 1992 Plymouth acclaim?
To remove the fuel tank from a 1992 Plymouth Acclaim, first ensure the vehicle is on a flat surface and disconnect the battery. Lift the rear of the car and support it securely with jack stands. Remove the fuel pump and fuel lines, then detach any straps or bolts securing the tank to the vehicle. Finally, carefully lower the tank and remove it from the vehicle.
How do you fold the rear seat down of a 93 Plymouth Acclaim?
It doesn't fold down, it bolts in.
How to change a rear cylinder in a 1991 Plymouth Acclaim?
First you have to jack the car up after loosening your lug nuts and then you remove the wheel. After you do this, you have to pull the brake drum off. Next, dis assemble the brakes then disconnect the brake line from the wheel cylinder. Then you remove the two bolts holding the wheel cylinder on and put the new one in. Re install the bolts, and brake line, put the brakes back on, put the drum back on and bleed the brakes. Put your wheel back on and drive away.
1989 4 cylinder Plymouth Acclaim Cylinder head torque specifics diagram?
There are 10 bolts. Start with the center bolt on radiator side and work outward in a circular pattern. The torque steps are 45,65,65 ftlbs and then a 90 degree turn.
How do you remove a radiator from a Plymouth acclaim?
To remove a radiator from a Plymouth Acclaim, first ensure the engine is cool, then disconnect the negative battery cable. Drain the coolant by removing the drain plug or lower radiator hose. Next, disconnect the upper and lower radiator hoses, as well as the transmission cooler lines if applicable. Finally, remove any mounting bolts or clips securing the radiator, and carefully lift it out of the engine bay.
How do you change transmission pan gasket on a 1994 Plymouth acclaim?
To change the transmission pan gasket on a 1994 Plymouth Acclaim, first, ensure the vehicle is on a level surface and securely raise it using jack stands. Remove the transmission pan bolts and carefully lower the pan to avoid spilling fluid. Clean the mating surfaces of the pan and transmission, then place the new gasket in position. Reattach the pan, tightening the bolts to the manufacturer's specifications, and refill the transmission fluid as needed.
How Rear Wheel cylinder 2000 Chevy Malibu?
remove rear wheel, remove brakes and cylinder is held on by 2 bolts from back of plate. remove bolts and brake line from cylinder !! somtimes you can take top nails holding brakes out to allow room to remove cylinder.
How Replace oil pan in 89 Plymouth acclaim?
To replace the oil pan on a 1989 Plymouth Acclaim, start by draining the engine oil and removing the oil filter. Next, lift the vehicle and support it securely, then remove any components obstructing the oil pan, such as the exhaust or crossmember. Unscrew the oil pan bolts and gently pry the pan off, cleaning the mating surfaces. Install the new oil pan with a new gasket, torque the bolts to the specified settings, and refill the engine with oil.
Where is the thermostat on a 1992 Plymouth acclaim?
The black radiator hose comes out of the upper left of the radiator. Follow it to where it connects to the engine block at the top center of the engine. It is just to the left of the ignition coil. That is the thermostat housing. Remove the bolts holding the housing, and the thermostat will be there.
How do you remove the heads on a Chevy 350?
take out the cylinder head bolts
