0
What else can I help you with?
Voltage frequency inverter dc or ac output?
An inverter changes a d.c. input to an a.c. output. Inverter is a device to change low volt DC to high volt AC 12 Dc to 220 Ac volt So many type of inverter of watts 500 watt 1000 watt 5000 watt
How much current flow in 1 watt bulb?
Everything Depends on the voltage supply ...... Current flow (Amp) = Watt / Voltage the Current flow will be 1 amp if voltage is 1 V the Current flow will be 0.5 amp if voltage is 2 V the Current flow will be 0.25 amp if voltage is 4 V and so on.......
Output power rating of PWSA card in Ultra BTS?
600 WATT
Amps times ohms equal?
voltage! measured in volts. current X resistance = voltage simple ohms law
What size cable required for3 phase 128 watt?
To answer this question a voltage is needed.
Can A 70 watt metal halide bulb be replaced with A 150 watt halide bulb?
No. A 70 Watt metal halide bulb can not be replaced with a 150 Watt halide bulb.
Can you replace a 100 watt metal halide lamp with a 70 watt metal halide lamp?
Yes, you can replace a 100-watt metal halide lamp with a 70-watt metal halide lamp, but it will result in lower light output. The 70-watt lamp will provide less brightness, which may not be suitable for applications requiring high illumination levels. Additionally, ensure that the fixture is compatible with the lower wattage to avoid any electrical issues.
What is the voltage at a 100 watt metal halide light bulb?
It depends......perhaps 7400 to 8500 initial lumens degrading to 5400 lumens.
How many fluorescent tubes equal 1000 watt metal halide light?
It would depend on the wattage of the fluorescent tubes. As a rough estimate, you would need about 6-8 standard 40-watt fluorescent tubes to approximate the light output of a 1000-watt metal halide bulb.
Can you use a 65 watt fluorescent bulb in a metal halide light fixture?
No, the ballast's output is not matched to operate a fluorescent bulb.
Can you run a 50 watt halide bulb on a 100 watt halide ballast?
No, it is not recommended to run a 50 watt halide bulb on a 100 watt halide ballast. The ballast should match the wattage of the bulb to ensure proper operation and to avoid potential damage to the bulb and ballast. It is best to use a ballast that is rated for the wattage of the bulb being used.
How many lumen in 100 watt metal halide?
A 100-watt metal halide lamp typically produces around 8,000 to 10,000 lumens, depending on the specific design and efficiency of the bulb. This lumen output can vary based on factors such as the manufacturer and the lamp's age. Metal halide lamps are known for their bright, white light, making them popular for outdoor and commercial lighting applications.
WILL 103 VOLTS LIGHT A 60 WATT LIGHT BULB?
Yes, a 103 volt source will light a 60 watt light bulb. The relationship of the bulb's wattage output at a lower voltage, as to the normal voltage that the bulb is rated to operate on, the light output will be lower.
What led equals 400 watt metal halid?
To equate the light output of LEDs to a 400-watt metal halide bulb, you typically need around 100 to 150 watts of LED lighting, depending on the specific type and efficiency of the LEDs used. Metal halide bulbs produce high-intensity light but are less energy-efficient compared to modern LED technology. LEDs also have a longer lifespan and emit less heat, making them a more sustainable choice for many applications. Therefore, when replacing a 400-watt metal halide, look for LED fixtures in the 100-150 watt range for similar light output.
How many lumens in a 70watt metal halide lamp?
From 20,000 to 23,000 lumens depending on the brand.Average figures:Incandescent: 10 lumens per wattHalogen 13 lumens per wattCFL (low-energy) 50 lumens per watt
What is the lumen's of a 70 watt metal halide lamp?
6000lm
What is the lumen output of a 70watt Metal Halide Recessed Down Light Since majority of the light output is through the reflector area in the Down Light you want to know the total reduction of light?
Typical LOR (lumen output ratio) of a reasonable MH downlight would be around 0.6 meaning that you get 60% of the lumen output of the lamp out of the fitting. Any manufacturer should be able to provide the LOR for a particular fitting
