What is the plug gap for a 1975 50 horsepower evinrude outboard motor?
The listed air gap for this engine is .030 in.
The 1975 year model, 100 hp Evinrude, requires a 50:1 fuel to oil ratio.
the 85 is the horsepower and the 75 is the year(1975)That is what I was told...I have same motor
Per Service Manual - Spark Plug Gap is .040" - Plug is Champion L77J4 Fuel Mix is 50:1 or 12 gallons Gas to 1 quart TC-W Outboard Motor Oil
1975 Long shaft
Is there a shear on a 1975 mercury 200 (20hp) outboard motor
Advertised Horsepower is---245HP @ 4000 RPMs.
What is the weight of a 1975 model 85 hp Johnson outboard motor compared to a 1990 model 140 hp Johnson outboard motor?
I have a Johnson 85 hp model no 85ESL75E 1975 longshaft low profile powershift II and it weighs 180kg apparently
Its a 1975 model
An 85 hp Mercury outboard, serial number 4294803 is from back in 1975.
i have 1975 manual I can photocopy 22 pages
The 1975 model, 45 hp Chrysler outboard, requires a 50:1 ratio, roughly one pint of 2 cycle oil, to six gallons of fuel.
The 1975 model, 7.5 hp Mercury outboard, requires a 50:1 ratio, roughly one pint of 2 cycle oil, to six gallons of fuel.
From 1975 when I owned a mac 3 it was fine at 25 to 1 regards
50:1 Which is one pint for six gallons of gas
That particular model was made in 1975. Put the model number in on google and you will find all the info you need on that motor
1975 model so it's 35-yo in 2010
It is a 70 HP 1975 Evinrude. The 5 indicates the year. I just bought a1975 Evinrude yesterday & looked up the number.
The 1975 model, 85 hp Johnson outboard requires a 50:1 ratio, one pint of 2 cycle oil, to six gallons of fuel.
From what I can find in serial number tables, your outboard is made in 1975. My refernce: http://www.marinshopen.se/Hj%c3%a4lpmedel/Modellguide/Mercury/3565Hk/tabid/107/Default.aspx
your motor is a 1975 200 20hp you can get more info here: http://www.autorepairmanuals.biz/site/573683/page/599300
Don't know that but where can I get a starter kit for a 1975 mercury 20hp 2 stroke motor. I can't pull the rope anymore. to old I guess
A 1975 Chrysler 30hp outboard requires a 50:1 fuel to two cycle oil mix.
The correct plug gap for the 1975 model, 75 hp Evinrude, is .032 in.
50:1 /16Oz.per 6 Gals. gas. I have the same outboard.
194 to 226 horsepower in a 1975 Ford car , looking in my Chilton repair manual
what is the oil/fuel mixture for 1975 15hp johnson
1975 20hp johnson
36years manufactured 1975
An 65 hp Mercury outboard, serial number 4266564 is a 1975 year model.
1975 model year.
Not positive but I think its 1975
The point setting on a 30hp Chrysler outboard would be .020in. if you are refiling your old points they should be set at .018in
280, to 300. NEW ANSWER: Straight out of the book. Advertised Horsepower is-175 HP @ 3600 RPMs. That engine STOCK didn't have HORSEPOWER it had torque
I had a Ford Granada inline 6 cylinder for ten years. I do not remember where was it referenced, but I remember it had 78 horsepower
210 to 260 horsepower and 320 to 355 ft / lbs torque depending on version according to my Chilton book
The Mercury outboard 4.5 with serial number 4273176 was created in two type mode which are the "M" and "ML" model. Both model types were manufactured in 1975.
175 Hp @ 3600 RPMs.
i've heard that it has about 400 hs
A 4.5hp Mercury outboard, serial number 4110432, is a 1975 year model.
The 105 hp Chrysler outboard requires an NGK 1966-1967 BR6S 1968-1974 BUHW 1975-1976 BUHX 1976-1983 BUHW
The 1975 Chevrolet K 20 has approximately 135 horsepower.
A 1974 Oldsmobile 455 V8 has horsepower of 275 to 400. The Oldsmobile 455 was last produced in the year of 1975.
Around 200 net hp
215 brake horsepower
ngk number is br9hs gapped at .030 and must use quicksilver 2stroke oil mixed at a 50:1 ratio
British Motor Heritage was created in 1975.
Advertised Horsepower and torque is... HP-----245 @ 4000 RPMs Torque.......355 ft. LBS. @ 3000 RPMs
ZIT'S are yummy 2 me XD
The 1975 model, 9.9 hp Johnson outboard requires a 50:1 ratio, one pint of 2 cycle oil, to six gallons of fuel.