The torque loading for head (and many others) bolts varies with the engine concerned. It is important to check the manufacturers handbook to ensure the correct loading is applied. It is also important to tighten the bolts on the sequence indicated in the manual and by increments to the final loading. If no sequence is given then it is good practice to tighten from the centre out.
For most 'standard' car engines it will be around 50 ft lb.
Add your answer:
What is the proper torque setting on head bolts for a 1963 Massey Ferguson model 65 diesel?
massey65 torque head bolts please
How do I replace the head gasket on a 1995 suzuki sidekick?
Remove the intake manifold, exhaust manifold, and then remove the head. Scrap off the old gasket and install a new one. Reinstall the head and Torque the head bolts in the proper sequence. Reinstall the intake and exhaust manifold torque the bolts to the proper torque. This is a major repair and not for a novice to try.
How do you replace the whole head gasket set on 1994 sidekick 4wd?
Remove the intake manifold, exhaust manifold, and then remove the head. Scrap off the old gasket and install a new one. Reinstall the head and Torque the head bolts in the proper sequence. Reinstall the intake and exhaust manifold torque the bolts to the proper torque. This is a major repair and not for a novice to try.
How much is the torque of 2c cylinder head bolts Toyota?
torque for 2c engine cylinder head bolts
Torque Specifications 1.9 L Ford 1995 Escort Connecting Rods and Head Bolts?
Head bolts are 44 psi tightened 3 times in the proper pattern
Torque setting for cylinder head bolts for a Skoda felicia?
torque setting for cylinder head bolts for a skoda felicia
What is the torque specs for head bolts on a Chevy 292 straight 6?
Torque for 292 head bolts is 95 ft lbs
To what torque must the bolts on the head of a 2000 Hyundai accent be tightened?
to what torque must the bolts on the head of a 2000 Hyundai accent be tightened?
What is the torque specification for Toyota Camry 1989 four cylinder head bolts?
1991 toyota camry head bolts torque specs
Torque specs for a 1995 Subaru impreza 2.2 head bolts?
Torque specs for a 1995 subaru impreza 2.2 head bolts?
What are the torque specs for 660 raptor head and hex bolts?
The torque specs for 660 raptor head and hex bolts is about 26 lbs.
Torque specification on head bolts on a Jinma tractor?
There are either eight or ten bolts on the head of Jinma tractor. The torque bolts require 95 to 105 foot pounds.
What are the head bolt torque specs for a 1999 Pontiac Grand Am 2.4 4cylender?
HEAD BOLT TORQUE For your 1999 PONTIAC GRAND AM: HEAD BOLT TORQUE FOOT POUNDS (FINAL TORQUE) TORQUE SEQUENCE --------- | 6 2 3 7 | | 5 1 4 8 | --------- STEP 1: TORQUE IN SEQUENCE TO 33 FT/LBS STEP 2: TURN AN ADDITIONAL 90 DEGREES RECHECK FINAL TORQUE IN SEQUENCE *** CAUTION *** ENGINE USES TORQUE TO YIELD HEAD BOLTS (TTY) THAT PERMANENTLY STRETCH DURING THE INITIAL INSTALLATION. NEW HEAD BOLTS MUST BE USED WHEN CYLINDER HEAD IS REPLACED OR RE-INSTALLED TO OBTAIN PROPER TORQUE. ALWAYS COAT BOLT THREADS WITH THE PROPER SEALANT.
How much should i torque the head bolts specs on a 3.1 V6?
You should torque the head bolts by alternating from and to end, working towards the center. The head bolts should be torqued in 40 pound intervals.
What is Toyota Camry cylinder head bolts torque specs?
The torque specs for a Toyota Camry cylinder head is 60 pounds for the inside bolts and 50 pounds for the site bolts. The cylinder head bolts should be tight from and to end alternating.
What are the torque values for the cylinder head of a 1997 24L Pontiac Grand Am?
For all the 2.3, 2.4L QUAD 4 engines, the head bolts are Torque to Yield. The porper torque value is 30ftlbs PLUS a 90 degree turn of the wrench. The bolts must be new every time ( NEVER REUSE OLD BOLTS). The torque values and proper sequence are including in the box the new bolts come with. BUT honestly, the torque value is 65ft lbs like all GM Chevy motors have been for eons.
What is the proper head torque for a 92 Geo Storm 1.6 engine?
the proper torque specification for the geo storm 1.6 engine is 58 ft lbs ... Always torque in a spiral from the center outwards. Make sure you cleaned up the threads in the block ith a chaser (NOT a tap) before proceeding. And oil the threads on the new head bolts. You should be able to turn the bolts all the way snug with your fingers if the threads are cleaned up correctly. Then torque in 3 stages to the final torque in a spiral from the inner bolts.
Torque on head bolts Oldsmobile 1974?
Cylinder head to block torque = 80 ft-lbs.
Head bolt torque for 6.6 gm duramax?
What is the torque spect for head bolts on duramax 6.6
Head bolts torque settings?
hi i am looking for the torque settings for a proton gen 2 cylinder head bolt and crank shaft bolts both big ends and main bearing bolts
What is the cylinder head torque on a Toyota Paseo?
The cylinder head on a Toyota Paseo requires 33 pounds of torque on the head bolts. If the bolts are over tighten the block can warp leading to a blown head gasket.
Torque specs on a head bolts for a 1991 yz 125?
The cylinder head bolt torque specification is 90 pounds. The cylinder head bolts should be torqued in 30 pound intervals.
Head torque 2.2 Chevy?
what is the torque setting for the head bolts on a 2007 chevy malibu with a 2.2L engine
1995 Mercury Tracer Torque specs for head bolts?
Torque sequence------------ l 93157 l l 862410 l ------------ Step 1: torque in sequence to 44 Ft/LBS Step 2: in sequence completely loosen all bolts Step : retorque all bolts in sequence to 44 Ft/LBS Step 4: in sequence turn an additional 90 degrees Step 5: in sequence turn an additional 90 degrees Recheck final torque in sequence***CAUTION*** engine uses Torque To yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.
What is the torque sequence of your head bolts for a Cadillac 4.5 engine?
The torque specs for a Cadillac depend on which engine it has. For most 425, 572, 368, and 500 engines, the torque for the head bolts is 115 ft. pounds. The torque for the cam bolts is 25 ft. pounds, and the torque for the valve covers is 10 ft. pounds.
Get the Answers App
