answersLogoWhite
Consumer Electronics
Technology

What is the proper way to connect an ammeter?

479480481

Top Answer
User Avatar
Logan smith
Answered 2020-09-09 07:21:10

An ammeter is a measuring device used to measure the electric current in a circuit. A voltmeter is connected in parallel with a device to measure its voltage, while an ammeter is connected in series with a device to measure its current.

123
๐Ÿ™
4
๐Ÿคจ
2
๐Ÿ˜ฎ
0
๐Ÿ˜‚
1
User Avatar
User Avatar
Anonymous
2020-09-19 02:30:55
Right. But, make sure - if you are using a VOM (combination volt-ohm-milliameter) your SWITCHED to "ammeter", not volt or ohm!

User Avatar
Md. Alamgir Hossain
Answered 2020-11-07 03:49:33
  • The most common way to measure current in a circuit is to break the circuit open and insert an โ€œammeterโ€ in series (in-line) with the circuit so that all electrons flowing through the circuit also have to go through the meter.Some digital meters, like the unit shown in the illustration, have a separate jack to insert the red test lead plug when measuring current.
012
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar
User Avatar
Up And Atom
2020-11-08 20:45:00
is this a copy paste competition?
User Avatar
Up And Atom
2020-11-08 20:45:59
sorry I commented on the wrong answer

User Avatar
dejan 22
Answered 2020-11-07 00:57:04

Windows, macOS, and Linux computers use the TCP/IP protocol to connect to other computers on a LAN or WAN. Connecting to a LAN or WAN requires either a wired connection or a wireless connection. A wired connection is usually done using a network cable.

webllena

012
๐Ÿ™
0
๐Ÿคจ
1
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar
User Avatar
D O'H
2020-11-08 19:41:51
dejan 22.ย  What question are you answering?

User Avatar
darshi ginu
Answered 2020-09-19 08:08:19

Think of the voltmeter and ammeter as galvanometers whose needles deflect with only a tiny bit of current. Now if you want to measure the current in a circuit without significantly changing the current in that circuit by introducing the meter, you must adjust this galvanometer such that it will add very, very little resistance to your circuit when placed in series with the circuit. The way this is accomplished is by putting a relatively low resistance in parallel with the galvanometer. The low resistance of the galvanometer in parallel with the low resistance of the “shunt” resistor will make an even lower resistance than either the shunt or the galvanometer. The voltmeter, on the other hand wants to measure the voltage dropped across either some part of the circuit load or the entire load which is also the source voltage. To do this we must put the meter in parallel with part of the load or all of the load. So we take our galvanometer, which has very little resistance and before exposing it to that large potential (voltage) difference, add a very large resistance, called a multiplier, in series with the galvanometer so that we are not creating a significant parallel path for current to flow. We are simultaneously protecting the galvanometer by sharply reducing the current that will flow through the galvanometer. OK, so our voltmeter is no more than a galvanometer with a high resistance multiplier resistor in series with it to dramatically lower the current through the meter and our ammeter is just a galvanometer with a low resistance shunt that can be in series, with the full current in the circuit, but whose resistance is lowered further by the shunt and which thereby prevents the galvanometer from the excess current that would damage the meter.

001
๐Ÿ™
1
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar
User Avatar
D O'H
2020-11-08 19:40:51
Can you please add the math that goes with your description, darshi ginu?

User Avatar
Miraj Miru
Answered 2020-07-14 19:29:14

To pardon electrical modern via a wire, the ammeter is used. You do utilizes it in imitation of excuse at all short electric currents and very full-size ones. However, proviso thou is a beginner, solely use such after pardon little currents. Large electrical currents can keep dangerous.

Connecting an ammeter in conformity with dimension cutting-edge only takes a not many minutes or less. However, from time to time human beings be brought pressured yet assume it’s even simple. For example, those might just connect the pair probes in imitation of the wire. The solution to connecting an ammeter efficiently is remembering to that amount the coalition is certain that cutting-edge pleasure drifts thru the ammeter, so salvo such was once a wire.

Set the present day kind switch. Ammeters can be old in imitation of measurement prescribe present day yet alternating current, additionally recognized as DC and AC current. If your anus is a battery, the modern intention remains to prescribe current. If ye control thine circuit with a rule supply, the type concerning modern-day desire depend concerning you control supply. There are DC and AC government substances as much well namely control materials to that amount pass you pick DC or AC voltage. So agreement thy control grant is put in in accordance with AC, employ the ammeter in accordance with AC. If it is a DC control supply, accept the ammeter in accordance with DC.

Examine the ammeter-calibrated scale. When contemporary flows via an ammeter, the fork about the meter intention pace across the calibrated scale. The construction concerning the reach to that amount the bone settles atop choice corresponds in accordance with the modern that is drift thru your ammeter. The range regarding the far-right cease regarding the meter corresponds in conformity with the most contemporary analyzing because of the particular range that the ammeter is accepted for. This maximum number is oft referred to according to as a full-scale reading.

Set the length multiplicator swap in imitation of its very best value. winnow the one of a kind degrees to that amount you ammeter has. One spread could stay because of amperes, any other milliamperes or every other microampere. However, keep in mind distinct ammeters wish bear distinct ranges, therefore check thine owner’s manual. Set the measure multiplicator change according to the best range. For this action pick the ampere range. And it's due to the fact amperes are a thousand times larger than milliamperes, then milliamperes are a thousand times large than microamperes.

Determine the full-scale studying because of the measure set. Multiply the setting concerning the length factor with the aid of the full-scale variety about the meter. The full-scale range about the meter is the variety regarding the meter as is of the far-right give up regarding the calibrated scale. It may remain 1, 2 yet 5 and anybody another number. Next, fall in with the full-scale variety by way of the measure multiplicator setting. If thine full-scale quantity was 1.5, and your thoroughness factor was embarked to milliamperes, the maximum present-day thou could dimension with your ammeter would keep 1.5 milliamperes, then 0.0015 amperes, in view that distribution milliamperes with the aid of 1,000 offer the modern-day among phrases regarding milliamperes.

Connect an easy circuit consequently up to expectation the modern-day choice glide via the ammeter. Connect the tremendous probe over the ammeter to the high-quality border on the power supply. Connect the terrible probe on the ammeter to certain quit regarding a resistor. Finally, connect the vile cease on the resistor in imitation of the negative end over the control supply. The ammeter is in modern times linked therefore that the present-day that flows thru the resistor will additionally waft thru the ammeter, also understand as an in-series connection.

001
๐Ÿ™
1
๐Ÿคจ
1
๐Ÿ˜ฎ
3
๐Ÿ˜‚
1

User Avatar
Wiki User
Answered 2016-06-12 22:17:06

Are u talking about a amp meter? If so there is 2 kinds one is a clip on that simply goes around the wire that u are wanting to check amps on.one other goes in line u will need to find a junction or cut the wire current goes in one side of the meter reads amps then out the other.with out loss of current. Be more specific next time then I can helped u much better.25 years experience industeral electrical tech.

+++

Actually, although 'amp meter' is closer to what it is, they are usually called 'ammeters', often in print as well as speech.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

User Avatar
Up And Atom
Answered 2020-11-08 20:44:03

It has to be connected in series. That is the only and correct answer.

012
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

User Avatar
HUDA SIDDIQUE
Answered 2020-09-18 10:03:10

proper way to connect ammeter is to connect in series

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
1
๐Ÿ˜‚
0

User Avatar
BODO
Answered 2020-11-09 18:06:31

w

012
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

User Avatar
Shermaine Body
Answered 2020-09-18 05:05:23

Dreadgod

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
2

User Avatar
Anonymous
Answered 2020-09-17 18:02:15

AROUND ONE WIRE OF A TWO WIRE SET FOR 110VAC

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
1
๐Ÿ˜‚
0
User Avatar
User Avatar
Anonymous
2020-09-17 18:02:31
IF IT'S THE "CLAMP ON

User Avatar
Anonymous
Answered 2020-07-12 10:27:15

How is your family

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar
User Avatar
Anonymous
2020-07-12 10:28:16
Howย  is your familyย 

User Avatar
Anonymous
Answered 2020-09-18 03:01:23

Which statement is true

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

User Avatar
Anonymous
Answered 2020-09-19 13:44:15

PHONE AND PRINTER

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
1

User Avatar
Anonymous
Answered 2020-08-30 15:41:44

In series with cercuit

001
๐Ÿ™
0
๐Ÿคจ
2
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

User Avatar
Anonymous
Answered 2020-09-19 00:16:10

pof

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

User Avatar
Anonymous
Answered 2020-09-17 21:38:39

Hhh

001
๐Ÿ™
1
๐Ÿคจ
1
๐Ÿ˜ฎ
1
๐Ÿ˜‚
1

User Avatar
Anonymous
Answered 2020-09-18 09:04:54

Bax

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


How do you connect an ammeter to a circuit?


connect ammeter in series with load.


Always connect the ammeter in series in a circuit


Connect ammeter in series and voltmeter in parallel to the circuit


HOW TO CONNECT AN AMMETER Always connect an ammeter in SERIES in a circuit. Always ensure that the ammeter has a higher reading range than the expected current load, including start-up spikes. An ammeter expected to read a steady current of 13A should have a max range of 20A.


The ammeter will only read when connected properly. If the meter is connected backwards, then the meter reads the wrong way. If it is a digital ammeter then it may not work at all.


The voltmeter is connected across the supply and the ammeter is connected in series with the supply.


To extend the range of an ammeter you have to connect a resistor in parallel with the meter coil.


To increase the range of an ammeter, you connect a very low impedance resistor in parallel with the ammeter.


the voltmeter is connected across the supply and the ammeter is connected in series with the supply


plug it into 2 of the wires so the electricity will flow through itAn ammeter is connected in series with the circuit



Dont know!!!!!!! ask the teacher and by the way, what is ammeter?


Disconnect the circuit power. After that, break the circuit, connect your ammeter in series with the circuit, and re-energize.


You use three CTs, one per line conductor, each feeding a separate ammeter,


Ammeter should be inserted in the place where we need to find the current. Care must be taken while inserting ammeter such that it is in series always. For example if we need to measure the current through any device, we have to connect the ammeter in series with tht device.


An ammeter theoretically has zero resistance. And real-life ammeters have very low resistance. So connecting an ammeter in parallel with a resistor will basically short it out. The vast majority of current will flow through the ammeter rather than the resistor.


To convert a galvanometer into an ammeter, you connect a suitable shunt resistance parallel to the coil of the galvanometer.The value of this shunt resistance is low. To convert a galvanometer into a voltmeter you connect a suitable high resistance in series with the coil of the galvanometer.


The ammeter is designed, on purpose, so as to have a very low resistance. Doing this will result in an excessive current.


That won't work. To convert an ammeter (a galvanometer is a very sensitive type of ammeter) you connect a high value resistor in series with it.


no matter what vehical it is, the proper way to disconnect a battery is to disconnect the ground side first ,then the positive side to reconnect it is exactly opposite you connect positive side irst then connect ground side ground side in case your not sure is the negative side of battery


In series with the element who's current you're hoping to measure..


A voltmeter must be placed in parallel with the circuit component across which the voltage appears. An ammeter must be placed in series with the circuit component through which the current passes.


A; It would be in practical by adding additional ammeters the accuracy will diminish


ammeter connect in series in circuit to measure the current, if the Ammeter have a high resistance it would effect the voltage value because there will be a drop voltage over the internal resistance of the Ammeter, so we desgin the ammeters with very low resistance...



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.