0
What else can I help you with?
Which is the default order of a router searching startup configuration information?
When a router boots up, it follows a default order to search for startup configuration information. First, it checks the non-volatile memory (NVRAM) for the startup configuration file, typically named "startup-config." If it doesn't find a valid configuration there, it may look for a configuration file in a TFTP server, and if that fails, the router will proceed with its default settings, often leading to a mode where no configurations are applied.
There is often a web?
There is often a web address printed on the bottom of the router, along with a username and password used for configuring the router. You can enter that address into your browser, using the username and password to access the router's configuration pages. Newer routers also often come with setup CDs that can walk you through that process by running an application on your computer that is connected to your router. If you need more help, please provide the brand and model number on the router and I'll be happy to assist!
How do you rename ssid?
To rename the network name (SSID) you will need to log in to your router, this is often done with a web browser (if the router did not come with its own software) using the routers address (which often starts 192.168.... ), enter the password to access the router's configuration settings and find the Network name/SSID section to enter the new name.
How do you setup a computer network?
If the computer network is to have internet, then you would need a modem connected via a phone line or cable connection. Then the modem is usually connected to a Router, that in turn connects to a "Switch". All the computers then connect to the Switch through ethernet cable (cat5 or cat6). One computer is often designated as the "Server", a central point to hold the programs and data for the other computers (clients) to use. INTERNET --> MODEM--> ROUTER --> SWITCH --> SERVER --> COMPUTERS (In some cases, the router can also serve as the switch as well).
What is main difference between a Layer 3 switch and a router?
Switches are Layer 2 devices only while Routers operate at Layer 3. Switches by definition transfer data frames by readingFrame'sDestination MAC address & sendingitout throughtheport to which mac address (if found in table) is connected. While Routers perform data transfer by reading IP Addresses on Packets. Switches connect devices within same network number while Routers can connect several networks & support different technologies for data transportation.
Why does my computer keep detecting my router then says a local connection area is unplugged?
This will often come up because the Router you are talking about would be a wireless router. The computer is sensing that an ethernet cable is not plugged in from the router to your computer. This will often come up because the Router you are talking about would be a wireless router. The computer is sensing that an ethernet cable is not plugged in from the router to your computer.
The word protocol is often used to describe diplomatic relationsgive an example of a diplomatic protocol?
Good manners are an example of a diplomatic protocol. Diplomatic protocols are often implied and unwritten and are used to build relationships between countries.
Term used for a data packet often implying a specific layer or protocol?
Protocol Data Unit (PDU)
How do you get a linksys befsr41 router to work?
To set up a Linksys BEFSR41 router, first connect it to your modem using an Ethernet cable plugged into the WAN port. Then, connect your computer to one of the LAN ports on the router. Access the router's configuration page by entering its default IP address (usually 192.168.1.1) in a web browser and logging in with the default credentials (often "admin" for both username and password). From there, you can configure your internet settings, set up Wi-Fi, and customize other features as needed.
Often equipped to act as hardware firewalls?
Router
Where is the acronynm of the Hypertext Transfer Protocol when in use?
The Hypertext Transfer Protocol is most often used when browing websites and webpages, in which case a URL often identifies where a client is and where they want to go next. This URL contains the acrononym for the Hypertext Transfer Protocol at the very beginning, stating to request information using this protocol.
Why switch is data link layer?
Data link layer refers to things that happen within a single network; that's what a switch does. Only a router (or equivalent device, which I would still consider a "router") is able to connect different networks.The different networks may use the same technology (for example, Ethernet and Ethernet), or different technologies (for example, Ethernet and Wi-Fi); a switch is only able to connect parts of a single network that use the same technology (often this will be Ethernet).
