0
Interlocks fitted to breakers suggest that a load is supplied from two separate sources. An example would be where one breaker is supplied from a utility source and the other breaker will be supplied from a generator source. To prevent both breakers from being on at the same time to supply the load, an interlock is placed across both breakers. This allows only one breaker to be on at a time. Manual interlocks allow a person to make the decision as to which power source will supply the load. Automatic transfer switches have built in interlocks and will sense where the source power is coming from. This type of system switches from one electrical source to another without any human intervention.
Wiki User
∙ 10y ago
Wiki User
∙ 13y agoA 240 Volt circuit breaker uses an interlock to shut down BOTH sides of a breaker when either experiences an overload condition. The interlock is essential to prevent electrocution and damage to electrical equipment.
Wiki User
∙ 12y agoits prevent breaker from closing by itself or remotely and manualy
Add your answer:
Earn +20 pts
What is a knockout in a circuit breaker panel?
A knockout is a pre stamped hole in a distribution panel. The metal slug in the pre stamped hole requires knocking or prying to remove it from the panel. Once the slug is removed from the hole, a cable connector is fitted through and secured with a lock nut on the inside of the panel. A wire cable is then threaded through the cable connector and held securely in place by the connectors wire clamp.
Why must a fuse or Switch never be fitted to the secondary of a CT circuit?
Secondary of a CT should never be opened to avoid damage to CT. Fuse or switch may lead to opening of CT secondary accidentally.
Difference between fuse and mcb?
CB MCB (i) Mechanism of CB is tripping relay. (i) Mechanism of MCB is tripping release (ii) It is used in HV system. (ii) It is used in LV system. (iii) Rupturing capacity is high . (iii) Rupturing capacity is low.
What would be a parallel circuit in your house?
== == A Parallel circuit is one where the current flows in several circuits (or 'branches') at the same time.In the house, the Main Breaker box (or fuse panel) is connected to the city's power lines. The current flows through the main circuit breaker and is then split into 2 or more circuits each of which is protected by its own circuit breaker.Envision a water pipe that is mounted horizontally in the attic. The pipe has 10 one inch holes cut into it, into these holes are fitted 10 one inch pipes that let water flow through each one as required (such as when the toilet is flushed, or the kitchen sink faucet is turned on).So, coming out of the Main Breaker box are several cables (each protected by its own smaller breaker), each going to a separate room, or area (outdoor patio, or detached garage).The reason for parallel electrical circuits is to limit the amount of current in each cable. If there was only one cable for the entire house, all of the current for every electrical device in the house would have to flow through the same cable, as opposed to each room (or area) having its own cable and only using as much current as is required for that room.I hope this helps, if so, please 'Recommend Contributor', and reply to this answer for more info, or a more detailed explanation.
How do you prevent heat loss in the home?
You should do all these things. * Have loft insulation fitted * Have cavity wall insulation fitted * Draught excluder placed by your doors * Carpet your house all the way round * Have double glazing fitted. You will save lots of valuable pounds.
What safety device is fitted to ensure a circuit breaker can not be racked out when closed?
A remote racking device is the name of a safety device that is fitted to ensure a circuit breaker cannot be racked out when closed.
What is an electrical isolator?
Something that doesn't let electricity throughAnswerAn isolator (UK terminology) or disconnector (US terminology) is a switch used to isolate a section of a circuit from any energised conductors, by presenting a visible break in the circuit. Isolators are not designed to break load currents (unless fitted with optional arc-breaking feature) or to break fault currents. In high-voltage systems, isolators are used in conjunction with circuit breakers -with the isolators opened after a circuit breaker has opened the circuit, and closed before the circuit breaker closes the circuit. For example, before one can perform maintenance work on, say, a high-voltage circuit breaker, the following sequence must be followed:the circuit breaker is opened, breaking the circuit.isolators located on either side of the circuit breaker are opened, presenting a visible break between the isolator and energised lines.temporary earth (ground) connections are applied to each side of the circuit breaker.barriers and warning signs are erected around the circuit breaker to define the permitted work area.a permit to work card, listing the work to be performed, and any potential hazards, is issued to the personnel who are to maintain the circuit breaker.
What is the difference between pv valve and pv breaker of tanker ship?
A globe type PV valve is fitted to a cargo tank to prevent over/under pressure, while a liquid filled PV breaker is fitted on the IG system, again to prevent over/under pressurisation of a cargo tank
Why bulb does not work when fitted in a circuit with switch?
because you are switch the hot leg, so it can be turn on an off.
What is the purpose of Inter-pole fitted in a DC generator?
to chancel the effect of the armature reaction.
What voltage should read at the outputs of a hundred amp breaker?
It depends on where the breaker is fitted. Is it installed in a panel in the US, Canada or another country which also uses the 60Hz, 120 Volts standard supply service?Or is it fitted in Europe or elsewhere using the 50Hz, 230 Volts standard?As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.The amperage of the breaker dont determine the voltage reading. If your panel is 120v every breaker regarding of amperage rating or size will still read 120v. but to answer your question as it reads... the voltage on the output should read the same voltage as the input or line side.. that is if the breaker is in the on position.
How do you earth a plug with 2 wires my heater says it must be earthed but came with a fitted plug and not earthed it has blown the plug twice any suggestions?
The heater has a three prong plug and the outlet has 2? If it has blown the fuse or circuit breaker, it is drawing more current than the circuit can handle. That is the purpose of the fuse. If you only have 2 prong outlets, it is probably mounted in a metal box that should be grounded. It may not be or it may be in a metal box but the box is not grounded. They make an adapter that has a tab you put behind the screw that is holding the outlet cover in place. Grounding the heater is not going to stop it from blowing the circuit. Try a different outlet, remove something that is on the same circuit or use a heavier fuse which is not always a good idea.
What is the purpose of a fuse in an electrical circuit?
The purpose of a fuse is to open an electronic circuit when current flow exceeds a certain amount, determined by the rating of the fuse. Opening a circuit under high current conditions can save electronic components from damaged and prevents overheating, which could cause a fire.
Which circuit breaker used for an electric clothes dryer?
To ensure you are using the correct rating of fuse simply divide the total wattage of your appliance by 250 and round up to the closest value. For example, a 1500 watt hair dryer should be fitted with a fuse equal to 1500 divided by 250 = 7amp
Can is use a 32v fuse instead of a 125v fuse?
No. If the voltage rating of a fuse is too low for the circuit in which it is fitted then, when the fuse operates (i.e. its link melts), the circuit voltage might maintain the resulting arc within the fuse, and it will fail to protect that circuit.
What is the purpose of the inertia switch fitted to the electrical supply of the fuel pump relay?
To stop fuel flow to engine in case of accident
How do you spot a 2 way mirror in fitting rooms?
You cannot. That would defeat the purpose. In most jurisdictions it is likely to be illegal to have them fitted.
