0
What is the relation ship between load displacement and deadweight?
Wiki User
∙ 11y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the relationship between the applied load and the force?
The relationship is linear. Nothing more can be said without more information in the question.
What is the relation between stress gradually applied and suddenly applied?
Stress suddenly applied load = 2 x stress gradually applied
What jobs are levers used in?
lifting heavy objects
What is the relationship between the amount of effort needed to lift the load and the distance of load from the fulcrum?
confusing
What is difference between chronological load curve and load duration curve?
Load duration curve represents re-arrangement of all load elements of chronological load curve in the order of descending magnitude. It illustrates the relationship between generating capacity requirements and capacity utilization.The area under the load duration curve and the corresponding chronological load curve is equal and represents total energy delivered by the generation station.
What is gross tons of a ship?
Not a simple queston to answer. In general practical terms, the gross or deadweight tonnage may be expressed as the all-up tonnage of a ship when loaded to the the legal limit of her load marks. It is NOT the weight of the ship. Nor is it the displacement. Peter Cottman.
What is the difference between a load-controlled tensile test and a displacement-controlled tensile test?
If the test is set to load-control , it means that the stress will not drop once the fracture become unstable. In displacement control the stress may drop at unstable fracture.
What is the relationship between the applied load and the force?
The relationship is linear. Nothing more can be said without more information in the question.
What is the relation between stress gradually applied and suddenly applied?
Stress suddenly applied load = 2 x stress gradually applied
What are the uses of spring balance?
A spring balance is a weighing device that utilizes the relation between the applied load and the deformation of a spring. It is widely used commercially.
What is the diesel consumption rate of a tractor?
That would depend on the displacement, rpms and the load it is be asked to bear.
Is it advisable to correct the power factor to unity?
power factor depends on the load being fed if the load is entirely resistive power factor will be unity ..if the load includes an inductor or capacitpr due to phase displacement between v and i the pf will be lag or lead respectievly
What happens on Ammeter when load is increased?
It depends on the configuration of the ammeter. If you have an ammeter with red on one side, green on the other, and a balance point in the center, the needle will go into the red when when load is increased in relation to the charge. If the load is decreased in relation to the charge, the needle will go into the green. If you have an ammeter with a numerical value (i.e. 30, 40, 50, etc.) then the needle will go up to the value of the load present in the system not in relation to the charge.
What is the relation between internal resistance and load resistance when current is constant in the circute?
The total resistance of a circuit is the sum of the supply's internal resistance and its load resistance, because they are in series with each other. This is true regardless of the magnitude of, or the variation in, the current.
What is the displacemet of the aircraft carrier USS Ronald Reagan?
Displacement: 101,000 to 104,000 tons full load
What is the difference between displacement and true power factor?
'Displacement power factor' is the technically-correct term used to describe the cosine of the phase angle (i.e. the angle by which the load current leads or lags the supply voltage) due to the reactance of a load. Usually, when we talk about the 'power factor' of a load, we mean 'displacement power factor'.However, another type of power factor can exist in a circuit, due to the presence of harmonics in the current waveform, due to non-linear loads such as SCR rectifiers. This type of power factor is temed 'distortion power factor', and may be corrected using filters.So, the terms 'displacement' and 'distortion' are used whenever it is necessary to clarify these different types of power factor.
How can you apply displacement controlled load with eccentricity on RC columns working inside ansys?
Use a enforced displacement boundary condition. Use a lot of substeps and force/moment reaction probes to know when you're at the load(s) you want. A free body diagram should tell you that.
