Impulse XI
53 7/16 on a 28-30 draw length
56 3/8 on a 30-32 draw length
30" is not a draw weight, it is a draw length. It is the length of the draw from the bow to the string when the bow is drawn.
Draw the bow to full draw and hold it. Have your assistant place a nail in the small round hole in the bottom of each pulley wheel and then slowly let the pressure off of the bow string. Unhook the looped bowstring from the metal string connectors and set aside. Slide the connectors up and away from the bow limbs and pull them out of the pulley wheels. Move the connectors to a new hole or position on the wheels (a higher hole if you want the draw length shorter or a lower hole if you want the draw length longer). Reconnect the string to the metal string connectors and draw the bow to full draw again. Have your assistant pull the nails out of the pulley wheels and then let the bow down slowly. This process can also be performed by using a bow press to depress the bow's limbs and then changing the draw length in the same manner.
38"
Without going to the bow shop, this method requires a hanging scale with a hook. Connect your string and pull down while measuring draw length between the string and handle. when you match your draw length, that is the corresponding weight.
what is the string length of a Mathew Mission compound bow
No, you cannot. The shorter connection will not fit the string/cable. Even if it did, the tension could damage the bow.
If it is a compound bow, the type of bow with the pulleys or "wheels" at the ends of the bowlimbs, there should be some way to adjust the draw-length of the bow itself; it may be best to consult someone at an archery shop for the best way to make such an adjustment. When using a Traditional bow -- a recurve or longbow, or other non-compound type -- the only "adjustment" is to simply pull the string back (in this case) to 27 inches; reducing the draw-length in this way also reduces the effective draw-weight of the bow. Also, when using a Traditional bow, and the archer has a longer draw-length than the bow is rated for (i.e., the archer's draw-length is 30 inches, but the bow is rated at 27 inches), it is always advisable to make sure the bow is designed to withstand the longer draw-length. Failure to do so can result in the catastrophic failure of the bow, and possibly serious injury to the archer. Increasing the draw-length of a traditional bow will also increase the effective draw-weight of the bow.
depending on the length of the bow which, i think should be 52", you'll need a 48" string.
48"
The general rule of thumb is that one inch of draw length will increase your speed by approximately 10 fps. This will vary from bow to bow and depends a lot on the draw length and poundage being changed.
The Bear Scout bow is a twin cam bow that can be adjusted for both draw length and draw weight. As the draw length increases so does the draw weight and vise-versa. The draw length and weight is determined by the amount of rotation the cams experience during a full draw cycle. For example, If the cams rotate 270 deg it will have a longer and stronger draw than if the cams only rotate 180 deg. With twin cam bows this rotation is determined by the % of string on each side of the cam. The front side of the cam contains the string that will dead end on the other limb while the rear side of the cam contains the string used to nock the arrow. The scout bow is equipped with cams that allow easy movement of the string back-n-forth from front to rear. First before adjusting, note the position of the brass nock that is pinched on the string somewhere by each cam. This position is important to remember for adjusting your bow in the correct direction. In order to adjust the rotation of the cams, the bow must be disassembled as stated in manual (push down on limbs and pull cam assembly off). Then unwind the string from the cam. You will notice that the cam can slide along the string. If you want to shorten the draw length and decrease the draw weight, then slide the string so the brass nock is on the front side of the cam. If you want to lengthen the draw length and increase the draw weight, then slide the string so the brass nock is on the rear side of the cam. Then do the same for the opposite cam. Note that the brass nocks must be in the same location on each cam. Then reassemble as stated in the manual. Tada your done and ready to shoot. I hope this was helpful…
Bear says bow string length is 86.125in & buss cable length 31in