0
What is the technical order for the Crushed Stone Crater Repair and Line of Sight Profile Measurement for Rapid Runway Repair is?
AFP
To 35e2-5-1
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is arc crater?
Arc crater is the depression in the molten metal created by the end of the welding electrode during the welding of metal.
What is the mission of the MOS marking team?
the mos team layouts of the minimuim operating strip, establishes travel routes, and ids crater size and location
Affecting factor of tool life in machinability?
The life of tool is affected by many factors such as: cutting speed, depth of cut, chip thickness, tool geometry, material or the cutting fluid and rigidity of machine. Physical and chemical properties of work material influence tool life by affecting form stability and rate of wear of tools. The nose radius tends to affect tool life.1. Cutting speed: Cutting speed has the greatest influence on tool life. As the cutting speed increases the temperature also rises. The heat is more concentrated on the tool than on the work and the hardness of the tool metrix changes so the relative increase in the hardness of the work accelerates the abrasive action. The criterion of the wear is dependent on the cutting speed because the predominant wear may be wear for flank or crater if cutting speed is increased.2. Feed and depth of cut: The tool life is influenced by the feed rate also. With a fine feed the area of chip passing over the tool face is greater than that of coarse feed for a given volume of swarf removal, but to offset this chip will be greater hence the resultant pressure will nullify the advantage.3. Tool Geometry: The tool life is also affected by tool geometry. A tool with large rake angle becomes weak as a large rake reduces the tool cross-section and the amount of metal to absorb the heat.4. Tool material: Physical and chemical properties of work material influence tool life by affecting form stability and rate of wear of tool.5. Cutting fluid: It reduces the coefficient of friction at the chip tool interface and increases tool life.
Who built the first hydrogen bomb?
US, 1952 Ivy Mike cryogenic liquid deuterium/tritium test device. The device itself, nicknamed "Sausage", measured 80 inches (2.03 m) in diameter and 244 inches (6.19 m) in height and weighed about 54 tons, its outer steel wall was 10 to 12 inches thick. It contained a triple thermos bottle holding the liquid fuel and a liquid hydrogen circulation system to keep the fuel cold. The device and all its tons of support equipment were on the island of Eugelab in Eniwetok atoll. When Mike was detonated, with a 10.4 megaton yield, the island and all the equipment turned into a crater and a cloud of radioactive fallout. The device was designed by Richard Garwin, at Los Alamos. The first one small enough to actually fit in an airplane bomb bay was tested in 1954 Castle Romeo, a device named Runt, a emergency version of which entered stockpile later that year as the EC-17 bomb, the next year a ribbon parachute was added to allow the bomber time to escape the blast upgrading it to the MK-17 bomb. The MK-17 was 6 feet diameter and so long only the B-36 bomb bay was big enough to hold it. The MK-17 went through 2 upgrade mods (MK-17 mod-1 and MK-17 mod-2). Changes to the fission primary of the MK-17 produced the MK-24 with the same dimensions. The MK-24 also went through 2 upgrade mods (MK-24 mod-1 and MK-24 mod-2). Both the MK-17 and MK-24 were retired from stockpile sometime between 1958 and 1961, as smaller lighter weight bombs were developed that other bombers and even fighters could deliver. Chuck Hansen: Swords of Armageddon
What two methods for filling the crater are used today?
Crushed Stone and Sand Grid
Which are the three type of crater repair methods?
Crushed stone, ballast rock, debris backfill
What problems did Apollo 11 have?
There was a technical problem, and the landing was not on spot, as there was a small crater there.
What dungeon comes after Dark Crater?
That is the last dungeon story-wise. There are other dungeons that you can get through wonder-mail though. If you want to get technical, Deep Dark Crater comes after Dark Crater.
Who signals the profile management team to commence upheaval checks?
Crater repair cheif.
The mat assembly area must be large enough to?
unfold both mats without hindering the crushed stone crater repair operations
Is the Copernicus Crater a Volcanic crater?
No. Copernicus crater is an impact crater.
What is the crater in a volcano?
Any place the volcano opens up is called a vent since it allows for the release of built up heat and gas. The main summit of the volcano is usually called the crater but I'm guessing there is probably something more technical that a geologist would call it. Hopefully this helps.
What is mount Etna's crater dimensions?
At the summit there are four craters: the Northeast Crater, Bucca Nuova Crater, Southeast Crater and Varagine Crater.
What is the Moon's largest crater?
The cheese crater. The cheese crater is the cheeseiest crater in all of cheese land.
What largest crater has a lake above it?
crater lake crater lake
Steep walled depression around volcano vent?
Volcanic crater.
