Want this question answered?
Carburize (Materials) BS 4360 43C is a structural grade like ASTM A 36 but with guranteed charpy properties:C .19 max, Si .5 max, Mn 1.5 maxUTS 62,400 psiYield Strength depends on thickness but up to 1.5-inch would be 35,000 psiCharpy impact tested at 0 degrees C (-32 Degrees F)minimum average impact toughness 27 J (20 ft lb)
BS1452 grade 200 is a cast iron grade with a tensile of 200 N/mm2. I have checked on my iron data base and can find no Indian equivalent to this specification. In the UK most stockists hold grade BS1452 grade 250 and with the slightly higher tensile it is commonly used as a suitable alternative to grade 200. I found further information on Cast Iron Specifications at the 'related link page'.
Yes. BS 6651 has been replaced by BS EN 62305.
BS standards are british standards EN standards are European Union standards. For individual differences you would need to look at the particular standard you are concerned with. There are many thousands.
S355 in bs
BS 4360 equivalent to IS:1161/1979
Astm a36
BS 3692 is not a grade...it refers to the name of British standard BS 3692 which contains the specifications of ISO metric precision hexagon bolts, screws and nuts. In this standard and other BS bolt standards, bolts are categorized into groups called grades such as grade 4.6 & 8.8... Example: Grade 4.6 : The first number (4) refers to 0.01 of minimum tensile strength of bolt (4/0.01=400n/mm2). This second number ( 6) refers to 10 times of the ratio between minimum yield strength and minimum tensile strength (yield strength/400=0.6 hence, yield strength =400X0.6=240) Hope this helps... Mohammed
Carburize (Materials) BS 4360 43C is a structural grade like ASTM A 36 but with guranteed charpy properties:C .19 max, Si .5 max, Mn 1.5 maxUTS 62,400 psiYield Strength depends on thickness but up to 1.5-inch would be 35,000 psiCharpy impact tested at 0 degrees C (-32 Degrees F)minimum average impact toughness 27 J (20 ft lb)
A. R. Fewell has written: 'The determination of softwood strength properties for grades, strength classes and laminated timber for BS 5268:Part2'
Weapon Skill (WS) Ballistic Skill (BS) Strength(S) Toughness (T) Wounds (W) Initiative (I) Attacks (A) Leadership (Ld) Armor Save (Sv)
bs it best or bs physics
MAPUA INSTITUTE OF TECHNOLOGY- first ABET accredited school in the PhilippinesAccredited ProgramsEngineeringChemical Engineering (BS ChE)Civil Engineering (BS CE)Computer Engineering (BS CpE)Electrical Engineering (BS EE)Electronics Engineering (BS ECE)Environmental and Sanitary Engineering (BS EnSE)Industrial Engineering (BS IE)Mechanical Engineering (BS ME)ComputingComputer Science (BS CS)Information Technology (BS IT)TECHNOLOGICAL INSTITUTE OF THE PHILIPPINES- Second ABET accredited school in the PhilippinesAccredited ProgramsTIP QUEZON CITY TIP MANILAEngineering EngineeringComputer Engineering (BS CpE) Chemical Engineering (BS ChE)Electrical Engineering (BS EE) Computer Engineering (BS CpE)Electronic Engineering (BS ECE) Electrical Engineering (BS EE)Industrial Engineering (BS IE) Electronics Engineering (BS ECE)Mechanical Engineering (BS ME) Industrial Engineering (BS IE)Sanitary Engineering (BS SE) Mechanical Engineering (BS ME)Computing ComputingComputer Science (BS CS) Computer Science (BS CS)Information System (BS IS) Information System (BS IS)Information Technology (BS IT) Information Technology (BS IT)
BS 5155 was withdrawn and superseded with BS EN 593. Here BS 5155 & BS EN 593 is the same.
STEEL Notes Type Of Steel Composition %C-Mn-Ni-Cr-Mo Condition Yield Stress (Mpa)Tensile Stress (Mpa) Elongation % BS 970 080M40(EN8) A medium strength steel. Suitable for stressed pins, shafts studs, keys etc. Available as rolled or normalised. Supplied as square bar, or round bar or flat. Constructural Steel 0.4% C0.8% Mn Normalised 280 550 16
4years
bs from iisc