Head Gaskets and Valve Covers
Nissan Stanza
Chevy 350
Late Model 1979-New Ford Mustangs

What is the torque pattern for a 1987 Stanza head?

363738

Top Answer
User Avatar
Wiki User
2008-01-06 04:19:29
2008-01-06 04:19:29

When installing the bolts tighten the two center bolts temporarily to 15 ft lbs and install the other head bolts loosely, then tighten all bolts to 22 ft lbs and then to 58 ft lbs, loosen all bolts completely and then retighten them to 22 ft lbs and then to a final torque of 54-61 ft lbs When torquing bolts start with the center bolts forward and aft and then to the left side of the center bolts and then to the right side of the center and so on

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

1987 Chevy head bolt torque 2.5L?

User Avatar

The 1987 Nissan cylinder had bolt torque specification is 140 pounds. The cylinder head bolts should be torqued in 45 pound intervals.

User Avatar

The head bolt torque for the Dodge 6 cylinder and V-8 engines is 50 ft. lbs. torque. If it is a diesel engine, the torque is 90.4 ft. lbs. Tighten the bolts by working from the center out, and alternating side to side. This prevents warping of the head.

User Avatar

what is the correct torque for a Toyota Corolla engine - 4E-FE, 1st generation engine?

User Avatar

22ft pounds first torque followed by 49 ft pounds final torque an d recheck in proper order

User Avatar

For the Z24i and KA24 engines, the "cylinder head to front cover" torque specification is 3 to 8 foot-pounds (or 4 to 10 Nm)

User Avatar

Get a manual on your car and it will give you the settings of the intake, exhaust bolts plus the head bolts and torque pattern.

User Avatar

The torque specs and pattern on the head bolts of a 1991 Toyota pickup with a 3.0 engine are 5, 4, 6, 3, 2, 7, 1, and 8. This sequence is started from the center of the head and requires 75 foot pounds of torque on each bolt.

User Avatar

The torque specs and pattern on the head bolts for a 1991 Toyota pickup with a 3.0 EFI is 50 foot pounds per bolt. The pattern is 4,5,6,3,7,2,8,1 with 1 being at the front of the engine.

User Avatar

The 1987 Kia 1.8 liter engine had bolt torque specification is 120 pounds. The camshaft bolt torque specification is 90 pounds.

User Avatar

As it is critical to do this correctly, I suggest you get a repair manual or ask a professional who has the correct sequence before them. Guessing is not an option.

User Avatar

65 foot pounds for re-used head bolts and 72 foot pounds for new head bolts.

User Avatar

I need a picture of a leganza deawoo head bolt tightening patern

User Avatar

For the 1987 Chevrolet S-10 with a 2.8 liter engine, the torque specs for the cylinder head bolts is 40 ft. lbs. The torque specs for the crankshaft damper bolt is 70 ft. lbs. For the oil pump bolts and the oxygen sensor, the torque is 30 ft. lbs.

User Avatar

Torque Value For 1987 R22, Per Haynes Manual - 58 ft lbs.

User Avatar

Ford CFord Cylinder Head Torque Specificationsylinder Head Torque Specifications

User Avatar

Work from center out alternating, snug up, torque to 55in pounds or 4.55 ftlbs.

User Avatar

The cylinder head bolt torque specs for a Mitsubishi 2.0 or 2.6 is 65 to 72 ft. lbs. cold. Torque sequence is as follows.

User Avatar

what is the head torque sequence for a 1991 pathfinder

User Avatar

Wallace has a good resource for torque specs. Check link.

User Avatar

what is head bolt torque spec gm 3.1

User Avatar

Cylinder head to block torque = 80 ft-lbs.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.