0
What is the voltage between each lead of a 480 volt three phase delta secondary?
Wiki User
∙ 12y ago
A 480 v three-phase system has 480 v between live lines and 277 v from each line to the neutral. This type of supply is common in North America for supplying for example small factories that need more power than a 120/208 v three-phase system can supply.
Wiki User
∙ 9y ago
Wiki User
∙ 12y agoThe voltage between each lead of a 480 volt three phase delta secondary is 480 volts.
Add your answer:
Earn +20 pts
How do you tell if you have delta or wye power?
In Europe, low-voltage three-phase distribution is by means of a four-wire system (three line conductors and a neutral) supplied from a wye-connected transformer secondary. In North America, low-voltage is supplied from a delta-connected transformer secondary, one phase of which is centre-tapped and earthed (grounded). The single-phase supply to residences is then supplied by that particular phase, giving 240 V line-to-line and 120 V line-to-neutral. You can tell if you have a delta power when the phase voltage is equal to the line voltage and that you have a star power when the phase voltage =root 3(THE LINE VOLTAGE).
How can three types of supply be obtained from the secondary side of a delta star transformer where the supply voltage is 11000 V?
The standard three-phase distribution transformer in the UK is a delta/star connection with a rated primary line voltage of 11 kV, and a nominal secondary line voltage of 400 V, giving a secondary phase voltage of 230 V.So, the secondary provides a three-phase, four-wire, system comprising three line conductors and a neutral conductor. The line-to-line (line voltage) voltage is 400 V and the line-to-neutral (phase voltage) voltage is 230 V.There are not 'three types' of supply obtained from this arrangement.
What is phase shift in three phase transformer?
The phase shift in three-phase transformer from winding of Transformer and determine by vectorgroup of transformer such as YNd1 High voltage connect to wye Low Voltage connect to delta so L.V. lag H.V 30 degree.Answer'Phase shift' or, more accurately, 'angular displacement', is the angle between the secondary line voltages and primary line voltages of a three-phase transformer.
What are the volts per phase on a 240 volt system?
By 'volts per phase', I assume you mean 'phase voltage' as opposed to 'line voltage'?It depends on the country in which you live. In North America, for example, the secondary output of a three-phase distribution transformer typically delta connected, 240 V corresponds to both the phase and line voltages.In other countries, where a three-phase distribution transformer's secondary is wye connected, 240 V is typically a phase voltage and 415 V is a line voltage.
What is the relationship of primary windings of a transformer to the secondary windings regarding output and input voltage?
The phase relationship between the primary voltage and the secondary voltage of a transformer is 180 degrees (typically) on single phase transformers. If working with three phase transformers, a zero phase shift is often used in Y/Y grounded transformers. If the transformer is wired Delta / Wye, the phase shift will be 30 degrees. I've seen transformers with a phase shift of 150 as well (quite abnormal, but it exists!) due to the starring and a delta / wye configuration. If you are looking at a transformer phasor diagram, this will show the phase shift between primary or secondary (three phase transformers). For single phase, there should be a drawing showing polarity markings - what goes in the polarity marking on the primary comes out on the secondary polarity marking.
What is the voltage phase shift between primary and secondary line voltages in star-delta transformer connection?
The voltage phase shift between primary and secondary connections in a transformer is 180 electrical degrees.
How do you tell if you have delta or wye power?
In Europe, low-voltage three-phase distribution is by means of a four-wire system (three line conductors and a neutral) supplied from a wye-connected transformer secondary. In North America, low-voltage is supplied from a delta-connected transformer secondary, one phase of which is centre-tapped and earthed (grounded). The single-phase supply to residences is then supplied by that particular phase, giving 240 V line-to-line and 120 V line-to-neutral. You can tell if you have a delta power when the phase voltage is equal to the line voltage and that you have a star power when the phase voltage =root 3(THE LINE VOLTAGE).
How can three types of supply be obtained from the secondary side of a delta star transformer where the supply voltage is 11000 V?
The standard three-phase distribution transformer in the UK is a delta/star connection with a rated primary line voltage of 11 kV, and a nominal secondary line voltage of 400 V, giving a secondary phase voltage of 230 V.So, the secondary provides a three-phase, four-wire, system comprising three line conductors and a neutral conductor. The line-to-line (line voltage) voltage is 400 V and the line-to-neutral (phase voltage) voltage is 230 V.There are not 'three types' of supply obtained from this arrangement.
What is phase shift in three phase transformer?
The phase shift in three-phase transformer from winding of Transformer and determine by vectorgroup of transformer such as YNd1 High voltage connect to wye Low Voltage connect to delta so L.V. lag H.V 30 degree.Answer'Phase shift' or, more accurately, 'angular displacement', is the angle between the secondary line voltages and primary line voltages of a three-phase transformer.
What are the volts per phase on a 240 volt system?
By 'volts per phase', I assume you mean 'phase voltage' as opposed to 'line voltage'?It depends on the country in which you live. In North America, for example, the secondary output of a three-phase distribution transformer typically delta connected, 240 V corresponds to both the phase and line voltages.In other countries, where a three-phase distribution transformer's secondary is wye connected, 240 V is typically a phase voltage and 415 V is a line voltage.
What is the relationship between phase and line values of current and voltage quantities for star and delta connected systems?
A: A DELTA transformer is a 1:1 voltage transfer delta to Y IS 1:2 voltage transfer. That is for 3 phase system, If the phases are not exactly matched or the voltage is not exactly right then on a Y setup there will be circulating current at the common node.
What is the relationship of primary windings of a transformer to the secondary windings regarding output and input voltage?
The phase relationship between the primary voltage and the secondary voltage of a transformer is 180 degrees (typically) on single phase transformers. If working with three phase transformers, a zero phase shift is often used in Y/Y grounded transformers. If the transformer is wired Delta / Wye, the phase shift will be 30 degrees. I've seen transformers with a phase shift of 150 as well (quite abnormal, but it exists!) due to the starring and a delta / wye configuration. If you are looking at a transformer phasor diagram, this will show the phase shift between primary or secondary (three phase transformers). For single phase, there should be a drawing showing polarity markings - what goes in the polarity marking on the primary comes out on the secondary polarity marking.
What is the connection of normal wire star or delta?
normally delta connection wired in 3 phase induction motor. during starting wiring is in Star and after running normal speed changeover to delta .beacause starting time its phase voltage equals less root3 times of line voltage ,line current and phase current equals. in Delta phase voltage and line voltage equals, and phase current equals root3 times line current
Why generally the high voltage side of transformer is delta connected?
I don't know what kind of transformer you are talking about, but most utility distribution transformers are star connected on the primary side.AnswerIt might be different in some other countries, but in the UK, three-phase distribution transformers are always connected in delta on their primary (high voltage) side, and in star (wye) on the secondary (low voltage) side. The primary line voltage is 11 kV, while the secondary line/phase voltages are 400 V and 230 V.In the United States and Canada, the primary winding is also connected in delta -however, the secondary side is also connected in delta, with one phase centre- tapped to provide the split-phase 240/120 V arrangement.The reason for using a delta connection is because three-phase high-voltage lines are supplied as three line conductors -there is no provision for a neutral- so there is no practical advantage in having a star-connected primary.
What is the formula use for calculation voltage and current in star and delta?
Balanced Star (Wye) Connected Systems:Line Voltage = 1.732 x Phase VoltageLine Current = Phase CurrentBalanced Delta Connected Systems:Line Voltage = Phase VoltageLine Current = 1.732 x Phase Current
How do you find angular displacement of transformer?
Angular displacement (sometimes called phase displacement) applies to three-phase transformers, whether a single three-phase transformer, or three single-phase transformers connected as three phase transformer bank. It is, to a three-phase transformer what additive/subtractive polarities are to a single-phase transformer.Angular displacement is one of a number of conditions that must be the same before two three-phase transformers (or transformer banks) are paralleled.'Angular displacement' is the angle by which the secondary line-to-line voltage lags the primary line-to-line voltage.Angular displacements for common connections are as follows:delta/delta transformers have an angular displacement of 0o or 180owye/wye transformers have an angular displacement of 0o or 180odelta/wye transformers have an angular displacement of 30o or 210owye/delta transformers have an angular displacement of 30o or 210oSo, for example, it is impossible to parallel a delta/delta or wye/wye transformer with a delta/wye or wye/delta transformer, as their angular displacements are different.Determining the angular displacement of a particular transformer configuration (wye-delta, etc.) can be done by drawing the phasor diagram for the complete transformer as follows:draw the primary phase voltagesdraw the primary line voltagesdraw the secondary phase voltagesdraw the secondary line voltagesmeasure the (angular displacement) between a secondary line voltage and its corresponding primary line voltage
Is transmission line voltage phase to phase?
Yes usually it would be phase to phase voltage because most transmission lines are set up in a delta configuration. This means that there is no neutral conductor to use as a reference. So any voltage would be measured with reference to another phase.CommentLet's get the terminology correct. The voltages between the three 'hot' lines of a three-phase, three- or four-wire, system are called 'line voltages' even though, in the case of a delta-connected system, they are numerically-equal to the corresponding phase voltages. Therefore, we call the conductors 'line conductors', not 'phase conductors'.There is simply no such thing as a 'phase-to-phase' voltage. Just think about it; you can only measure a voltage acrossan individual phase, so how can you possible measure a voltage 'phase-to-phase' -I mean, where would you place a voltmeter to do that?For a delta system, the line voltage (or line-to-line) voltage is numerically equal to the phase voltage (notphase-to-phase). For a star (or 'wye') system, the line voltage is equal to 1.73 x the phase voltage.
