0
When the anvil and spindle end are brought in contact, the edge of the circular scale should be at the zero of the sleeve (linear scale) and the zero of the circular scale should be opposite to the datum line of the sleeve. If the zero is not coinciding with the datum line, there will be a positive or negative zero error as shown in figure below. When the anvil and spindle end are brought in contact, the edge of the circular scale should be at the zero of the sleeve (linear scale) and the zero of the circular scale should be opposite to the datum line of the sleeve. If the zero is not coinciding with the datum line, there will be a positive or negative zero error as shown in figure below. When the anvil and spindle end are brought in contact, the edge of the circular scale should be at the zero of the sleeve (linear scale) and the zero of the circular scale should be opposite to the datum line of the sleeve. If the zero is not coinciding with the datum line, there will be a positive or negative zero error as shown in figure below.
Wiki User
∙ 15y ago
Wiki User
∙ 11y agoThe gap between the zero of the main scale division and zero of the circular scale division when the circular scale is tightly fixed is known as zero errror of micrometer screw gauge.
Add your answer:
Earn +20 pts
What is the 'zero error' in vernier calipers and micrometer screw gauge?
The zero error in the vernier calipers and micrometer screw gauge when the O mark on the main scale is not in line with the pointer.
What do you understand by zero error of a measuring instrument?
It is a defect in a measuring device (Vernier Callipers & Screw Gauge) & zero error is caused by an incorrect position of the zero point.
Can 47mm be azero error in screw gauge?
yes
What is a zero error?
if the zero line of vernier scale is not conciding with main scale the zero error exists.Knowing the zero error necessary correction can be made to find correct measurement..Such a correction is called zero correction
How do you take readings from a micrometer screw gauge?
The first step is to find the zero error and hence the zero correction. Rotate the micrometer until the fixed and movable jaws contact each other - not too hard and not too soft but just right, you should geta feel for this. Rarely will a micrometer will read zero. You need to figure out the zero error. It may be positive or negative. If the zero error is positive then the zero correction is negative and vicevers. Now open the micrometer and insert the object to be measured and close the micrometer with ideally the same sense of pressure you felt when you found the zero error. Now read the micrometer. You add the zero correction to get the true value.
How do you find zero error of screw gauge?
Take a measurement with nothing in the gauge. That reading is the zero-error.
What is the 'zero error' in vernier calipers and micrometer screw gauge?
The zero error in the vernier calipers and micrometer screw gauge when the O mark on the main scale is not in line with the pointer.
How do you find the zero error and zero correction in sgrew gauge?
we can find the zero error by closing the jaw of screw guage if the zero of main scale(MS) is concide with the zero of circular scale (CS) there is no zero error and if they are not concide there is a zero error in screw guage .
What do you understand by zero error of a measuring instrument?
It is a defect in a measuring device (Vernier Callipers & Screw Gauge) & zero error is caused by an incorrect position of the zero point.
Can 47mm be azero error in screw gauge?
yes
What is a zero error?
if the zero line of vernier scale is not conciding with main scale the zero error exists.Knowing the zero error necessary correction can be made to find correct measurement..Such a correction is called zero correction
How do you take readings from a micrometer screw gauge?
The first step is to find the zero error and hence the zero correction. Rotate the micrometer until the fixed and movable jaws contact each other - not too hard and not too soft but just right, you should geta feel for this. Rarely will a micrometer will read zero. You need to figure out the zero error. It may be positive or negative. If the zero error is positive then the zero correction is negative and vicevers. Now open the micrometer and insert the object to be measured and close the micrometer with ideally the same sense of pressure you felt when you found the zero error. Now read the micrometer. You add the zero correction to get the true value.
Why is screw gauge commonly called as micrometer screw gauge?
A micrometer screw gauge is commonly known as a micrometer. This is a form of calipers used for measuring small dimensions. Screw gauge in extensively used in the engineering field for obtaining precision measurements. The article describes the principle and main parts of a basic micrometer screw gauge.
Why does micrometre screw gauge work the way it does?
the screw gauge is an instrument which is used to measure length of an object.... the least count of an screw gauge can be found as follow.... l.c= pitch of the screw gauge no of divisions on main scale
What is the Difference between screw gauge and spherometer?
The difference between screw gauge and spherometer is that spherometer can measure the dimensions of spherical surfaces but screw gauge cannot
Why is the instrument called a screw gauge?
Because it can measure gauge of wire and has screw type structure.
What is Zeroing Error?
Suppose say you have plastic rule new one. There you will be having zero marking. When you have to measure the length of a rod then you would keep zero marking at one end of the rod and the marking where the other extreme of the rod is taken to be length of the rod. say it is at 4 cm. So 4cm is the length. And suppose the ruler is an old one whose edge got damaged. Now you don't have zero marking so visible there. So you have keep the end of the rod at say 1 cm marking. Now the error that we commit is known as zero error. Here the error is positive. ie +1 cm. So as the other end of the rod is at 5cm marking then the correct length is got by applying zero correction. As zero error is +1 cm, then zero correction would be -1 cm So the correct length 5-1 ie 4 cm. Same way in case of vernier, if zero of vernier is at left side of zero of main scale, then the zero error is negative. If zero of vernier is right side of zero of main scale then error is +ve as we have seen in the earlier old ruler case. Same way in case of screw gauge as the head scale zero is above pitch line then error is negative and as head scale zero is below pitch line then zero error is positive.
