0
Always start with the highest scale, than work your way down until you get a midscale reading. If you start with a low scale, you will overrange the meter, which can damage it in severe cases (especially the older analog meter movements).
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What could be the tendencies for the voltmeter if the voltages to be measured exceed the range?
You'd potentially damage the meter. Whether you do or not is immaterial; if the meter cannot measure the range of voltages you are expecting, it will not give accurate readings over that voltage range, thus you should not use it. Buy a different meter that will measure over that voltage range, or use a voltage divider circuit to get a lower voltage at a certain ratio of what is actually in the circuit (this may be difficult to do, or very simple depending on the circuit tested - the key is you do not want to load the circuit with the voltage divider network).
When measuring an unknown voltage with an analog VOM you should first?
For any value turn the multimeter to the highest scale in the value that you are measuring. By doing this you will not overload the meter by using a lower scale to measure a higher value.
How do you measure voltage?
Voltage can be measured using the difference between the potentiel between two ends of wire or by using a volt-meter. You can easily measure volt by volt or multimeter but remember voltage always measure across the components but in parallel
What measuring instrument is used to measure potential difference?
To Measure Voltage or potential difference you can use volt meter, there are diferent methode to measure DC voltage and AC Voltage.use a AVO meter and you can choose Voltage in each voltage range on the selector.a Volt meter instrument you can find it by manual methode and digital .Dont forget to read manual book before you will measure the voltage.Comment'Potential difference' is exactly the same thing as 'voltage'; they are synonymous.
What happens inside a voltmeter when you switch it from a lower to a higher voltage range?
When you switch a voltmeter from a lower to a higher voltage range, an additional resistor is added in series with the meter, increasing the voltage necessary to create the same voltage drop across or current flow through the actual meter movement.
What could be the tendencies for the voltmeter if the voltages to be measured exceed the range?
You'd potentially damage the meter. Whether you do or not is immaterial; if the meter cannot measure the range of voltages you are expecting, it will not give accurate readings over that voltage range, thus you should not use it. Buy a different meter that will measure over that voltage range, or use a voltage divider circuit to get a lower voltage at a certain ratio of what is actually in the circuit (this may be difficult to do, or very simple depending on the circuit tested - the key is you do not want to load the circuit with the voltage divider network).
When measuring an unknown voltage with an analog VOM you should first?
For any value turn the multimeter to the highest scale in the value that you are measuring. By doing this you will not overload the meter by using a lower scale to measure a higher value.
What is the maximum voltage the meter can handle?
Depends on the meter. If unknown, to be safe do not exceed the value of the highest range.
How do you measure voltage?
Voltage can be measured using the difference between the potentiel between two ends of wire or by using a volt-meter. You can easily measure volt by volt or multimeter but remember voltage always measure across the components but in parallel
Why you must put at highest range when you measure current or voltage?
You start at the highest range, because you don't want to damage the meter. You then bring the range selector down, incrementally, until the reading is in the lower, most accurate portion of the scale.
What measuring instrument is used to measure potential difference?
To Measure Voltage or potential difference you can use volt meter, there are diferent methode to measure DC voltage and AC Voltage.use a AVO meter and you can choose Voltage in each voltage range on the selector.a Volt meter instrument you can find it by manual methode and digital .Dont forget to read manual book before you will measure the voltage.Comment'Potential difference' is exactly the same thing as 'voltage'; they are synonymous.
What happens inside a voltmeter when you switch it from a lower to a higher voltage range?
When you switch a voltmeter from a lower to a higher voltage range, an additional resistor is added in series with the meter, increasing the voltage necessary to create the same voltage drop across or current flow through the actual meter movement.
The meters function range switch is set to read DC voltage in the 20 Volt range The meter displays a 1 in the most significant digit position What does this indicate?
the meter measured a voltage of 1 v at the point under test.
An ammeter and voltage range are measure the current and voltage electric lamp if mistake meter interchange what will happen?
1. Voltmeter has high impedance and hence will restrict the current severely.a) Electric Bulb will not glowb) The Ammeter will just measure the current that Voltmeter allows and since this current is much smaller than actual current nothing will happen to ammeter.c) The Voltmeter will measure the Voltage that is being applied.d) This will allow you to measure the resistance of the Voltmeter.VR=V/I
What range should the voltmeter be set prior to taking a voltage measurement?
If the voltage is completely unknown, a voltmeter should be set to the maximum range first, then stepped down to an accurate level.
Why should voltage be determined using highest range available first?
To keep from cooking your meter.
Why is it important to set a meter to the highest voltage range before connecting it into a circuit?
Sorry idont know
