answersLogoWhite

0

Always start with the highest scale, than work your way down until you get a midscale reading. If you start with a low scale, you will overrange the meter, which can damage it in severe cases (especially the older analog meter movements).

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Engineering

What could be the tendencies for the voltmeter if the voltages to be measured exceed the range?

You'd potentially damage the meter. Whether you do or not is immaterial; if the meter cannot measure the range of voltages you are expecting, it will not give accurate readings over that voltage range, thus you should not use it. Buy a different meter that will measure over that voltage range, or use a voltage divider circuit to get a lower voltage at a certain ratio of what is actually in the circuit (this may be difficult to do, or very simple depending on the circuit tested - the key is you do not want to load the circuit with the voltage divider network).


When measuring an unknown voltage with an analog VOM you should first?

For any value turn the multimeter to the highest scale in the value that you are measuring. By doing this you will not overload the meter by using a lower scale to measure a higher value.


A voltage drop across a component is measured by placing the Meter in?

A voltage drop across a component is measured by placing the meter in parallel with the component. This configuration allows the meter to measure the potential difference across the component, providing an accurate reading of the voltage drop. It's important to ensure the meter is set to the appropriate voltage range to avoid damage and obtain precise measurements.


How do you measure voltage?

Voltage can be measured using the difference between the potentiel between two ends of wire or by using a volt-meter. You can easily measure volt by volt or multimeter but remember voltage always measure across the components but in parallel


Where do you set meter when checking for ripple?

When checking for ripple on a power supply, you should set the meter to the AC voltage setting. Connect the meter probes across the output terminals of the power supply while it is under load, if possible. This allows you to measure any AC voltage fluctuations (ripple) superimposed on the DC output. Ensure that the range is appropriate for the expected ripple voltage level.

Related Questions

How to use a volt meter to measure electrical voltage accurately?

To measure electrical voltage accurately using a volt meter, first ensure the meter is set to the appropriate voltage range. Connect the red probe to the positive terminal and the black probe to the negative terminal of the circuit. Read the voltage displayed on the meter and record the measurement.


What could be the tendencies for the voltmeter if the voltages to be measured exceed the range?

You'd potentially damage the meter. Whether you do or not is immaterial; if the meter cannot measure the range of voltages you are expecting, it will not give accurate readings over that voltage range, thus you should not use it. Buy a different meter that will measure over that voltage range, or use a voltage divider circuit to get a lower voltage at a certain ratio of what is actually in the circuit (this may be difficult to do, or very simple depending on the circuit tested - the key is you do not want to load the circuit with the voltage divider network).


When measuring an unknown voltage with an analog VOM you should first?

For any value turn the multimeter to the highest scale in the value that you are measuring. By doing this you will not overload the meter by using a lower scale to measure a higher value.


A voltage drop across a component is measured by placing the Meter in?

A voltage drop across a component is measured by placing the meter in parallel with the component. This configuration allows the meter to measure the potential difference across the component, providing an accurate reading of the voltage drop. It's important to ensure the meter is set to the appropriate voltage range to avoid damage and obtain precise measurements.


What DVM voltage range do you use to measure house current voltage 110V or 120V Why?

To measure house current voltage, a digital voltmeter (DVM) is typically set to the 200V AC range. This range is suitable for measuring standard household voltages, which in the U.S. typically fluctuate between 110V and 120V. Using this range ensures accuracy and prevents damage to the meter, as it can comfortably handle the expected voltage without exceeding its limits.


What is the maximum voltage the meter can handle?

The maximum voltage the meter can handle is typically indicated in the meter's specifications or user manual. It is important to ensure that the voltage being measured does not exceed this maximum limit to prevent damage to the meter or risk of electric shock.


How do you measure voltage?

Voltage can be measured using the difference between the potentiel between two ends of wire or by using a volt-meter. You can easily measure volt by volt or multimeter but remember voltage always measure across the components but in parallel


Where do you set meter when checking for ripple?

When checking for ripple on a power supply, you should set the meter to the AC voltage setting. Connect the meter probes across the output terminals of the power supply while it is under load, if possible. This allows you to measure any AC voltage fluctuations (ripple) superimposed on the DC output. Ensure that the range is appropriate for the expected ripple voltage level.


What measuring instrument is used to measure potential difference?

To Measure Voltage or potential difference you can use volt meter, there are diferent methode to measure DC voltage and AC Voltage.use a AVO meter and you can choose Voltage in each voltage range on the selector.a Volt meter instrument you can find it by manual methode and digital .Dont forget to read manual book before you will measure the voltage.Comment'Potential difference' is exactly the same thing as 'voltage'; they are synonymous.


What does infinity mean on a volt meter?

On a voltmeter, infinity typically indicates that the resistance is too high to measure, suggesting an open circuit or that the voltage source is not connected. It may also appear when the voltage reading exceeds the maximum range of the meter. In practical terms, it means there is no measurable voltage or current flowing in the circuit being tested.


An ammeter and voltage range are measure the current and voltage electric lamp if mistake meter interchange what will happen?

1. Voltmeter has high impedance and hence will restrict the current severely.a) Electric Bulb will not glowb) The Ammeter will just measure the current that Voltmeter allows and since this current is much smaller than actual current nothing will happen to ammeter.c) The Voltmeter will measure the Voltage that is being applied.d) This will allow you to measure the resistance of the Voltmeter.VR=V/I


Why you must put at highest range when you measure current or voltage?

You start at the highest range, because you don't want to damage the meter. You then bring the range selector down, incrementally, until the reading is in the lower, most accurate portion of the scale.