0
What mode must be in to configure IP address on a Cisco router?
Wiki User
∙ 11y ago
interface mode
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What router prompt can you use the router rip command?
On a cisco router you would go into privilege-exec mode (enable) and then into "configure terminal" mode. From there you can use the router rip command.
Which command sequence will permit access to five router virtual terminal lines with a password of cisco?
router>enable router#configure terminal router(config)#line vty 0 4 router(config-line)#password cisco router(config-line)#login to configure router with telnet you must set up password or secret for privilieged mode.
What is setup mode?
When a Cisco router is booted up for the first time, or is reloaded, the router will look into its Non-Volatile RAM (NVRAM) for the startup configuration file. Setup Mode is usedto configure a Cisco router or switch after start up to create a startup configuration file.
What router mode is required to configure a router?
127.0.0.1
What is the command used to get into global configuration mode on a cisco router?
On user exec mode type enable. When inside the privilege mode type configure terminal. You will then be sitting into global config after this. Please see below example: Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#
What does it mean when a user sees the command prompt Router config-if?
On a Cisco router, that means that you entered interface configuration mode; any command you give will affect the selected interface. For example, you may have given the commands:Router>enableRouter#configure terminalRouter(config)#interface FastEthernet 1/0Router(config-if)#On a Cisco router, that means that you entered interface configuration mode; any command you give will affect the selected interface. For example, you may have given the commands:Router>enableRouter#configure terminalRouter(config)#interface FastEthernet 1/0Router(config-if)#On a Cisco router, that means that you entered interface configuration mode; any command you give will affect the selected interface. For example, you may have given the commands:Router>enableRouter#configure terminalRouter(config)#interface FastEthernet 1/0Router(config-if)#On a Cisco router, that means that you entered interface configuration mode; any command you give will affect the selected interface. For example, you may have given the commands:Router>enableRouter#configure terminalRouter(config)#interface FastEthernet 1/0Router(config-if)#
Which mode enables you to view and change the configuration of a Cisco router?
Global Configuration Mode.
Which router configuration mode would an administrator use to configure the router for SSH or Telnet login?
line
Starting at the enable mode prompt what commands would you type to configure IP address 192.168.1.1 on interface E0?
I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#
What are router modes?
#Configure terminal for configuration mode #exit for previous mode #ctrl+z for set up mode
Which router configuration mode would an administrator use to configure the router for SSH or Telnet login access?
line
How do you enter your router ip so you can change your channel setting?
It depends on how your router was configured. If it uses DHCP service you can't change IP address at all. If you want to be able to change IP address you need to configure it to manual mode and set IP address manually.
