answersLogoWhite

0


Best Answer

anemick

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What patient is most at risk for fluid overload?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

What is risk analysis and risk exposure and what are the techniques you can use to mitigate risk?

Once the risks have been identified, you need to answer two main questions for each identified risk: 1. What are the odds that the risk will occur, 2. If it does occur, what will its impact be on the project objectives? You get the answers by performing risk analysis. There are two main forms of Risk Analysis: 1. Qualitative Risk Analysis & 2. Quantitative Risk Analysis You Mitigate Risks by first analyzing the risks and then taking steps to ensure that the risks are prevented.handled during the course of your project execution


What is standard commercial risk?

It is the standards of commercial business risk. BOOM!


How can you tell difference in motor oil and hydraulic fluid?

you can smell it hydrolic oil has a distinct smell to it AnswerHydraulic fluid is almost always thinner than motor oil. Answermotor oil is slightly slick if you rub it between you're fingers. hydraulic fluid will fell the same as brake fluid when rubbed between you're fingers. motor oil (new) will (typicly) be a darker shade as well. hydraulic fluid is normally clear or very close to clear.note: you should not leave either of these fluid's on you're skin. you should wash hands as soon as you are done handling them.


Consider the risk management planning of a construction project and match the sections of the risk management plan to their examples?

Methodologies - Meetings will be held weekly to plan, discuss, and analyze risks Budgeting - Risk management activities will amount to $8,500 Timing - Project risk jwq_04 will be reviewed monthly Roles and responsibilities - Ned Brown is responsible for risk 'tfr_07' You - are so effin lazy


Risk analysis is used to verify the cause of potential risks that a network may face What is a known phase of risk analysis?

Asset identification

Related questions

What is overload Explain whether overload is good or bad?

Overload is working to hard or pushing past your limits. it is bad because it increases your risk of injury.


What population group is at the highest risk for iron overload?

men


What danger exists in the majority of liver biopsy procedures?

In most cases, there is little risk to the patient from the biopsy procedure.


Why are people with iron overload at increased risk for infections?

Iron-rich blood favors growth of bacteria


What is the major risk of a nasogastric tube?

The most serious risk is that the patient will inhale some of the stomach contents into the lungs (aspiration). This may lead to bronchial infections and aspiration pneumonia.


How can changes in mental function increase a patient's risk accident and injury?

How can changes in mental functions increase a patient 's risk of accident and injury


How do you avoid risk?

Be watchful, alert and patient as you drive.


How the speakerphone function of the front desk telephone system can be used without violating patient confidentiality?

Speakerphone can only be used if there is nobody else in the room except for the doctor or patient. Otherwise the risk of violating patient confidentiality is at risk.


What are the nurse's responsibilities and duties in rendering care and services in an an abscond risk patient?

The nurses responsibilities and duties in rendering care and services to a patient who is at risk for absconding or becoming AWOL are to supervise and observe these at risk patients. Oftentimes, these patients will require a 1 on 1 aide to accompany them throughout the facility or hospital that the patient is in.


What risks exist for the patient in undergoing an impedance phlebography?

Impedance phlebography is painless and safe. It presents no risk to the patient.


What are the electrical specifications needed to operate the tanning bed?

Most tanning beds require 220 volts. Most homes are not wired to supply this kind of power. It is best to call a certified electrician to install a dedicated circuit to avoid the risk of electrical overload.


Ia cranial irradiation indicative of an acute lymphocytic leukemia patient?

On some high risk protocols it is used in the second delayed intensification phase. Even though there was no evidence of blasts in the spinal fluid. It is used prophalactically.