0
What percentage of electrical accidents where caused by unsafe acts?
Wiki User
∙ 9y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Three electrical hazards that may be present at a construction site are?
This may come from wet conditions, overhead power lines, and overloaded circuits but there are three main types of electrical hazards: Shock, Arc Flash and Blast and most electrical accidents result from one of the following three factors: unsafe equipment or installation, unsafe environment, or unsafe work practices.
Why is poor earthing a problem?
It is unsafe.
How do you wire a 220 volt two speed pump?
In certain cities specifically - and in many countries generally - any work on circuits carrying mains service voltages as high as 220V to 240V is considered to be unsafe to do unless you are a licensed electrician.Not only unsafe but also it is illegal in all states of Australia.If you're asking this question you shouldn't be installing an electrical service.This type of question usually means you aren't ready to do this yourself. Study some electrical training material and the National Electrical Code or call a professional electrician.If someone were to give you a more detailed answer here, you might attempt to do something you shouldn't be doing, and that may cost someone a shock, a home fire, or their life.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any workANDalways use an electricians test meter having metal-tipped probes(not a simple proximity voltage indicator)to insure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How does different types of soil affect the type of electrical systems?
The only thing I can think of to such a vague question is; the grounding rods would have to be buried deeper in sandy, or marshy soil. Is this what you're after, or do you mean the construction and location of a powerplant? Different types soil have different electrical resistance properties. The higher the resistance in the soil the greater effect on the systems ability to establish a ground. A ground is used for multiple reasons, one being the return path for a 120volt system the other being a fault path for all systems. The lower the resistance at ground the quicker a fault will reach maximum current and opening of the protective device (less chance for fire to result). When the resistance of the soil is above a certain level measured with a ground resistance tester, normal excepted practices are no longer useful. There are many different methods some chemically applied some mechanically applied that can be utilized to reduce the resistance, the most suitable method is generally selected based on past experience and/or exceptability by the engineer responsible for the project. There are many things that affect the ability of soil to conduct electricity, as well as disapate it. Not only at the time of the test, but permanently. Without this ground and/or return path an electrical system becomes unsafe, unpredictable, and in most cases damaging to the 120v equipment that is connected to it.
Should old wiring be replaced?
There is no requirement to replace old wiring unless new changes are being done to an old circuit that does not meet current code, in this case all the old wiring in that circuit must be replaced.It is entirely up to you if you want to replace old wiring or leave it as is (even if it looks unsafe) when no new changes are being made to the old circuit (e.g. you open a wall to do plumbing work and find antique "knob and tube" wiring with insulation problems - you do NOT need to replace any of this old wiring if you did not change its circuit in any way).Many houses in this area have unsafe 2 prong outlets installed in the 1950s that were designed for use interchangeably on 115V 15A and 230V 8A circuits, but their design allows 115V 15A, 115V 20A, or 230V 8A plugs to be inserted without the user knowing they are plugging into an incorrect circuit. But unless something else is changed on a circuit containing these unsafe outlets they may all be left as they are, but every one of these unsafe outlets on the circuit must be replaced with safe 2 prong if anything is changed (3 prong if the circuit is upgraded to 3 wire grounded wiring).About the only thing that could force rewiring the entire building is replacing an old screw in fuse box with a modern breaker box, as this changed to feed end for all circuits.----------------------------------------------------------------------------------------------------------------------------------------------If the wiring has rubber insulation for the conductors you should definitely replace it with modern pvc-based wiring. To protect your electrical outlets and appliances - and also for safety reasons - you should also upgrade the breaker box. If you have old wires which are made of copper that has pvc-based insulation you can leave them as they are but only if they are still in good condition. If the wires are made of aluminum or if they don't look safe - for instance if the insulation is damaged - you should replace them immediately.AnswerOld wiring may be safe if left alone, not overloaded or abused, and was originally "up to code". However, old rubber insulation with cloth coverings can become brittle and literally turn to dust if jiggled. This often occurs in overhead lighting outlets where heat from lights has dried and damaged the insulation. These old installations must be replaced if they are to be touched in any serious way (e.g., undoing clamps or other fasteners), otherwise they become unsafe. In other words, you should not simply pull out the old fixtures and devices and install new ones; you will need new wiring, and if you're getting new wiring, you should (must) get new circuit breakers.You can expect your main electrical panel and meter to last 30 to 40 years before they start to need to be replaced. The wiring in the wall can last a bit longer but when it gets to be 50 to 60 years old you're better off replacing it if you can.AnswerIn the late 1940s a type of cable called "Romex" was introduced in the United States, using PVC insulation for the individual copper conductors with a paper wrap and braided fabric overwrap. It is usually black or silver in color. This type of wiring is still safe today, although early Romex cables didn't contain a third earth ground wire, as required by current electrical codes. Houses with this type of wiring usually have outlets with just two slots, lacking the third hole for 3-prong plugs, although sometimes homeowners have replaced the outlets with the 3-prong type in violation of the National Electric Code (NEC). Current Romex cables have a third copper conductor that connects to earth ground and the outer jacket is molded PVC plastic instead of braided fabric.Take a look at your fuse box or breaker box. If it still contains the old screw-in fuses, chances are that the wiring in the house is outdated and should all be upgraded to modern Romex or "NM" type cable.
What percentage of accidents caused by unsafe acts?
50%
What percentage of accidents are caused by unsafe acts?
100 percent
What are the different causes of accidents?
Direct: Accidents that are caused by hazardous materials Indirect: Accidents caused by unsafe acts or conditions
What percent of accidents were caused by unsafe acts of people?
100
Three electrical hazards that may be present at a construction site are?
This may come from wet conditions, overhead power lines, and overloaded circuits but there are three main types of electrical hazards: Shock, Arc Flash and Blast and most electrical accidents result from one of the following three factors: unsafe equipment or installation, unsafe environment, or unsafe work practices.
What is the number one unsafe driving behavior that leads to accidents?
texting
What makes electrical power unsafe?
the shock
What are the causes of industrial disaster?
• The main cause of disasters in industry is because of employment of uneducated / illiterate people which sometimes results in huge lose of money and lives or sometimes results in huge lose in money. • Other Conditions of causes of industrial accidents can be broken down into two broad categories: unsafe conditions and unsafe acts. The causes of industrial accidents that pertain to unsafe conditions can include insufficient workspace lighting, excessive noise, slippery or unsafe flooring, extreme temperature exposure, inadequate protection when working with machinery or hazardous materials, unstable structures, electrical problems, machine malfunction or failure, and more. The causes of industrial accidents that involve unsafe acts can include actions or failures to act which result in injury. This can be a result of employee negligence but employers, organizations, and product manufacturers can also be liable for the causes of industrial accidents Smartq, answers for smart and a better life
What are Causes of industrial disaster?
• The main cause of disasters in industry is because of employment of uneducated / illiterate people which sometimes results in huge lose of money and lives or sometimes results in huge lose in money. • Other Conditions of causes of industrial accidents can be broken down into two broad categories: unsafe conditions and unsafe acts. The causes of industrial accidents that pertain to unsafe conditions can include insufficient workspace lighting, excessive noise, slippery or unsafe flooring, extreme temperature exposure, inadequate protection when working with machinery or hazardous materials, unstable structures, electrical problems, machine malfunction or failure, and more. The causes of industrial accidents that involve unsafe acts can include actions or failures to act which result in injury. This can be a result of employee negligence but employers, organizations, and product manufacturers can also be liable for the causes of industrial accidents Smartq, answers for smart and a better life
How do accidents take place due to unsafe condition or defective tools?
Most accidents take place due the negligence or conditions which make it prone to accident
What was the most unsafe car ever made?
The Ford Pinto had a tendency to explode even in minor accidents
What are the ethical issues to do with selling an unsafe electrical appliance?
the company could be sewed
