0
What prevents transformer laminationsfrom shorting to the adjacent laminations?
Wiki User
∙ 13y ago
You need to prevent transformer laminations from shorting to each other because, otherwise, there would be eddy currents that affect the Q of the transformer, effectively impacting its efficiency. They would also cause the transformer to run hot.
If the laminations were not insulated from each other, they would constitute a one-turn shorted winding, with high internal current. Usually, the laminations, in the shape of an E, are inserted into the windings alternately from each end, enhancing magnetic coupling while not causing the one-turn short.
This is the same issue involving routing a conductor through a hole in a panel - the hole must be relieved, or slotted, to prevent eddy current, or (better) both conductors must be routed through the same hole, balancing the current, resulting in no eddy current.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is a welding transformer?
A welding transformer is an electrical transformer used in welding power supply. It pulls relatively low current drawn from the mains power (typically limited to 15 A to avoid tripping the circuit breaker) and converts it to the typical 50 A to 500 A used in arc welding and higher currents used in spot welding. The main difference between a Normal Step Down Transformer & a Welding transformer , is Not only to Step Down ( lower ) the outlet supply voltage and at the same time increase the Available Output Circuit Current, but to be also able withstand the Short Circuit Conditions on the Welding Output Side and especially for the Magnetic ( Iron Lamination Core ) Part of the Transformer. This Magnetic Path difference prevents the Supply side Electrical Circuit from Oveloading , espcially during the Striking of the Arc, when the Welding Electrode & the Welding Job touch to initiate an Arc, after which the Welding Electrode is lifted slightly by Experience, to maintain the required weld flow. A Normal Transformer of equivalent rating will not be able witstand this operation without burning out.
What is welding transformer?
A welding transformer is an electrical transformer used in welding power supply. It pulls relatively low current drawn from the mains power (typically limited to 15 A to avoid tripping the circuit breaker) and converts it to the typical 50 A to 500 A used in arc welding and higher currents used in spot welding. The main difference between a Normal Step Down Transformer & a Welding transformer , is Not only to Step Down ( lower ) the outlet supply voltage and at the same time increase the Available Output Circuit Current, but to be also able withstand the Short Circuit Conditions on the Welding Output Side and especially for the Magnetic ( Iron Lamination Core ) Part of the Transformer. This Magnetic Path difference prevents the Supply side Electrical Circuit from Oveloading , espcially during the Striking of the Arc, when the Welding Electrode & the Welding Job touch to initiate an Arc, after which the Welding Electrode is lifted slightly by Experience, to maintain the required weld flow. A Normal Transformer of equivalent rating will not be able witstand this operation without burning out.
How does an earthing transformer work?
Measurements of electric currentsAnswerA current transformer allows high values of a.c. current to be measured using an ammeter designed to measure lower-values of a.c. current. At the same time, it electrically isolates the primary circuit from the secondary circuit -essential if the primary circuit is part of a high-voltage system. CTs are also used to monitor primary currents for the operation of high-voltage protection relays.
What happens when a switch in a series circuit is opened?
it prevents electricity to flow. i hope that is right
How does the foam reduce heat loss?
Foam contains pockets of trapped air which prevents conduction.
IS Using the Fill Handle to copy formulas prevents the Excel user from having to retype formulas in adjacent cells?
Yes, using the Fill Handle is one way of copying formulas, and by copying formulas you can prevent the need to retype the formulas in those cells.
Is it correct that synaptic clefts prevents an impulse from being transmitted directly from one neuron to another?
Yes, that is correct. The synaptic cleft is a small gap between neurons, and it prevents direct transmission of impulses. When an impulse reaches the end of a neuron, it triggers the release of chemical messengers called neurotransmitters into the synaptic cleft. These neurotransmitters then bind to receptors on the adjacent neuron, allowing the impulse to be transmitted indirectly.
What is a welding transformer?
A welding transformer is an electrical transformer used in welding power supply. It pulls relatively low current drawn from the mains power (typically limited to 15 A to avoid tripping the circuit breaker) and converts it to the typical 50 A to 500 A used in arc welding and higher currents used in spot welding. The main difference between a Normal Step Down Transformer & a Welding transformer , is Not only to Step Down ( lower ) the outlet supply voltage and at the same time increase the Available Output Circuit Current, but to be also able withstand the Short Circuit Conditions on the Welding Output Side and especially for the Magnetic ( Iron Lamination Core ) Part of the Transformer. This Magnetic Path difference prevents the Supply side Electrical Circuit from Oveloading , espcially during the Striking of the Arc, when the Welding Electrode & the Welding Job touch to initiate an Arc, after which the Welding Electrode is lifted slightly by Experience, to maintain the required weld flow. A Normal Transformer of equivalent rating will not be able witstand this operation without burning out.
What is welding transformer?
A welding transformer is an electrical transformer used in welding power supply. It pulls relatively low current drawn from the mains power (typically limited to 15 A to avoid tripping the circuit breaker) and converts it to the typical 50 A to 500 A used in arc welding and higher currents used in spot welding. The main difference between a Normal Step Down Transformer & a Welding transformer , is Not only to Step Down ( lower ) the outlet supply voltage and at the same time increase the Available Output Circuit Current, but to be also able withstand the Short Circuit Conditions on the Welding Output Side and especially for the Magnetic ( Iron Lamination Core ) Part of the Transformer. This Magnetic Path difference prevents the Supply side Electrical Circuit from Oveloading , espcially during the Striking of the Arc, when the Welding Electrode & the Welding Job touch to initiate an Arc, after which the Welding Electrode is lifted slightly by Experience, to maintain the required weld flow. A Normal Transformer of equivalent rating will not be able witstand this operation without burning out.
The vitamin that prevents beriberi is?
The nutrient that prevents beriberi
Why there is always a neutral wire in the supply of electricity to home?
For any electricity supply there has to be a pair of wires to carry the electric current. One of the wires is connected to earth at the transformer where the power comes from. That one is called the neutral. They can't both be grounded so only one of them is, and that prevents a buildup of static electricity.
What is an alveolar rupture?
An alveolar rapture refers to a situation where the alveolus raptures as a result of increased trans alveolar pressure with less pressure in the adjacent intestinal space. The rapture is dangerous because the amount of pulmonary congestion or obstruction that prevents the expansion of the lung is immeasurable, thereby leaving no criteria for safe pressures.
What prevents leaves from drooping?
Adequate water intake prevents leaves from drooping.
A thermos bottle has a shiny interior What type of heat transfer does it prevent?
It prevents heat loss through radiation.It prevents heat loss through radiation.It prevents heat loss through radiation.It prevents heat loss through radiation.
What is the side effect of metal detectors?
The side effect of metal detectors is that it prevents the use of weapons and it also prevents violent crimes. The side effect of metal detectors is that it prevents the use of weapons and it also prevents violent crimes.
What prevents food or liquids from getting into lungs?
What prevents food from getting into the lungs is an Aorta.
The prevents food or liquids from getting into the lungs.?
What prevents food from getting into the lungs is an Aorta.
