0
Would depend on the gun and size scope tube. The tube would be either 1" or 30mm. Could be side mount top mount etc...More info needed
Wiki User
∙ 14y ago
Wiki User
∙ 14y agoalmost always high
if you mount the scope far forward you may be able to get away with medium
Add your answer:
Earn +20 pts
If I have a Savage Axis 308 and a Nikon Pro staff scope what kind of rings should I use to mount it?
Assuming that your scope is a 3x9x40 scope,then medium height rings will do the job.If it is a 3x9x50mm scope,then you will need a set of high scope rings.
What size rings do you use to mount a 56mm scope?
Depends on the tube diameter and profile of your weapon.
What kind of scope rings do you need for a Glenfield model 25?
Just today I put weaver rings on mine. They have a 3/8 dovetail base and 1" scope rings. I had short 1" rings but I could not remove my bolt for cleaning. The rings I replaced the rings with the above mentioned. 3/8 dovetail mount 1" rings fro scope mounting see thru mounts for use of iron sights And the most important part of all is the 7/8 rise of the new mounts.
Would an SVD scope fit on an AK 47?
No scope with an SVD mount is designed for the use on an AK mount. The mounting mechanism is slightly different and so is the scope height.
Can you use a real M14 scope mount on an airsoft gun?
No
How do you scope a rifle?
You are asking this question in the Shotgun category, so I must say that you don't scope a shotgun. Here's the basics on mounting the scope on a rifle. ( Assuming you have a scope mount on the rifle.) 1. Place the bottom half of the scope rings on the rifle first (Without the scope attached.) 2. Place the scope on the bottom half of the rings and adjust the scope mounts to comfortably fit your eye. When adjusted, tighten down the bottom half of scope rings to the rifle mount. ( The scope should have one cross hair adjustment at the top and one on the right.) 3. Place the scope in the rings and then put the top half of the rings on. Tighten them down, but not VICE tight, just loose. You still want to move the scope some. 4. Look through the scope and align the cross hairs level with the rifle barrel. The Vertical line should be straight up and down at a right angle with the barrel. 5. when you have the scope adjusted to your eye and the barrel of the rifle, tighten the top scope rings in a crisscross pattern a little at a time. Don't vice one down then go to the next one. Do it a few turns on each one until they are tight. A final note. If you have a small screw hole and screw at the back end of the scope mount (on the rifle) you may want to place the rear scope ring against that screw. This is a scope stop. This will keep the scope from moving back from the recoil. Some scope mounts have a long pad at the rear of the scope mount that acts the same way. It's usually necessary on high powered rifles not 22's. You most certainly can and should scope your shotguns as long as your state allows the use of scopes on them. I have scopes on all of my shotguns, and especially my slug gun!
How do you put a scope on a crosman tac 77 elite air rifle?
Most people have trouble mounting scopes. 1. Mount the rear scope base ring on the rifle first. Just the bottom half. Make it tight 2. Mount the front bottom half of the scope ring next. Use the scope to align the fit to your eve. Do not mount the top of the scope rings in this step. 3. with the scope adjusted to your eye mount the top of the scope rings but not real tight just snug. Look through the scope to make sure the cross-hairs are aligned with the barrel. 4. with an Allen wrench or screwdriver tighten down the rings using a crossover pattern. (left rear screw. front right screw. right rear screw. left front screw) a little at a time until tight. ) Now do the same to the other scope ring. Do not over tighten and strip out the screw holes. 5. most people try to put the rings on the scope first then try to put in on the rifle. This never works it will always come loose. The scope ring bases have to be mounted on the rifle first, then the scope comes last. your next step is aligning the scope to your target but you didn't ask about that so I'll leave that for another question
What size base and rings for a 270 rifle?
depends on the rifle and the scope. Most scopes will use 1 inch rings for that type rifle.
Can a Tasco 3-9X 50mm scope be mounted on a Winchester 22 cal rifle model?
While anything is possible,why would you want to use a scope of that power and objective size on a .22 cal.rifle?If your receiver has a built in 3/8in receiver rail then you may be hard pressed to find rings of the significant height to mount a scope of that size.I would recommend that you get a scope of 4X power.That is all that is needed for the maximum affect range of a .22cal rifle.
What kind of gun mount should you use for your JC Higgins Model 45?
What do you mean by "gun mount". Do you want to display it on a wall? Are you referring to putting a scope on it?
What mount would I need to put a modern scope on a JC Higgins 101.16 I would want to mount a Simmons .22 Mag Series. Is this possible?
Your J.C.Higgins is a sears name that was made by Savage.It is the model 6,or 87.I would use these madel numbers to cross reference the correct scope base and rings for your firearm.I would look at the old redfield mounnts as they made these for a lot of older model firearms.Good luck in your search.
Can you mount a scope on a 50 cal Thompson center New England that is not drilled?
It will require that the rifle be drilled and tapped for scope mounts. Some small rifles (usually .22 rimfire) can use a dovetail mount, but those rifles are made with the dovetail grooves, and they will not work with a heavy recoiling caliber. There are a very few scope mounts that use existing rear sight bases to mount the scope, but it will be very far forward on a T/C, and need a long eye relief scope. Your best course would be to have a smith do a professional D&T for your rifle- relatively cheap to do.
