answersLogoWhite

0

Would depend on the gun and size scope tube. The tube would be either 1" or 30mm. Could be side mount top mount etc...More info needed

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

If I have a Savage Axis 308 and a Nikon Pro staff scope what kind of rings should I use to mount it?

Assuming that your scope is a 3x9x40 scope,then medium height rings will do the job.If it is a 3x9x50mm scope,then you will need a set of high scope rings.


What size rings do you use to mount a 56mm scope?

Depends on the tube diameter and profile of your weapon.


What kind of scope rings do you need for a Glenfield model 25?

Just today I put weaver rings on mine. They have a 3/8 dovetail base and 1" scope rings. I had short 1" rings but I could not remove my bolt for cleaning. The rings I replaced the rings with the above mentioned. 3/8 dovetail mount 1" rings fro scope mounting see thru mounts for use of iron sights And the most important part of all is the 7/8 rise of the new mounts.


Would an SVD scope fit on an AK 47?

No scope with an SVD mount is designed for the use on an AK mount. The mounting mechanism is slightly different and so is the scope height.


How do you scope a rifle?

You are asking this question in the Shotgun category, so I must say that you don't scope a shotgun. Here's the basics on mounting the scope on a rifle. ( Assuming you have a scope mount on the rifle.) 1. Place the bottom half of the scope rings on the rifle first (Without the scope attached.) 2. Place the scope on the bottom half of the rings and adjust the scope mounts to comfortably fit your eye. When adjusted, tighten down the bottom half of scope rings to the rifle mount. ( The scope should have one cross hair adjustment at the top and one on the right.) 3. Place the scope in the rings and then put the top half of the rings on. Tighten them down, but not VICE tight, just loose. You still want to move the scope some. 4. Look through the scope and align the cross hairs level with the rifle barrel. The Vertical line should be straight up and down at a right angle with the barrel. 5. when you have the scope adjusted to your eye and the barrel of the rifle, tighten the top scope rings in a crisscross pattern a little at a time. Don't vice one down then go to the next one. Do it a few turns on each one until they are tight. A final note. If you have a small screw hole and screw at the back end of the scope mount (on the rifle) you may want to place the rear scope ring against that screw. This is a scope stop. This will keep the scope from moving back from the recoil. Some scope mounts have a long pad at the rear of the scope mount that acts the same way. It's usually necessary on high powered rifles not 22's. You most certainly can and should scope your shotguns as long as your state allows the use of scopes on them. I have scopes on all of my shotguns, and especially my slug gun!


Can you use a real M14 scope mount on an airsoft gun?

No


How do you put a scope on a crosman tac 77 elite air rifle?

Most people have trouble mounting scopes. 1. Mount the rear scope base ring on the rifle first. Just the bottom half. Make it tight 2. Mount the front bottom half of the scope ring next. Use the scope to align the fit to your eve. Do not mount the top of the scope rings in this step. 3. with the scope adjusted to your eye mount the top of the scope rings but not real tight just snug. Look through the scope to make sure the cross-hairs are aligned with the barrel. 4. with an Allen wrench or screwdriver tighten down the rings using a crossover pattern. (left rear screw. front right screw. right rear screw. left front screw) a little at a time until tight. ) Now do the same to the other scope ring. Do not over tighten and strip out the screw holes. 5. most people try to put the rings on the scope first then try to put in on the rifle. This never works it will always come loose. The scope ring bases have to be mounted on the rifle first, then the scope comes last. your next step is aligning the scope to your target but you didn't ask about that so I'll leave that for another question


What size screws are used in Maynard Buehler scope rings?

Maynard Buehler scope rings typically use 6-48 screws for the mounting hardware. These screws provide a secure attachment for the scope to the rings. It's always recommended to check the specific model for precise requirements, as variations may exist.


What size base and rings for a 270 rifle?

depends on the rifle and the scope. Most scopes will use 1 inch rings for that type rifle.


How do you remove a weaver side mount from a vintage j 4 scope?

To remove a Weaver side mount from a vintage J 4 scope, first ensure the rifle is unloaded and in a safe position. Use a compatible screwdriver to carefully remove the screws securing the mount to the scope and the rifle's receiver. Once the screws are removed, gently slide the mount off the scope, taking care not to damage the scope's finish. If the mount is stubborn, a light tapping with a soft mallet may help to loosen it.


What are the three rings on the western field ELT 3-9x33 scope used for?

The three rings on the Western Field ELT 3-9x33 scope are typically used for mounting the scope securely to a rifle. They provide stability and alignment, ensuring that the scope maintains its position during use. Additionally, the rings can help with adjusting the height and eye relief for optimal viewing. Proper installation is crucial for accuracy and reliability when aiming.


What kind of gun mount should you use for your JC Higgins Model 45?

What do you mean by "gun mount". Do you want to display it on a wall? Are you referring to putting a scope on it?