0
What should be length of an earth eletrode for standard earthing?
Wiki User
∙ 8y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
When is earthing required?
As it's a safety factor, earthing is essential and mandatory. It's an electrical connection between the exposed metallic parts of an electrical appliance or installation and the earth, regarded to have zero potential. Proper earthing provides an alternative and easy path for leakage or faulty current to flow. It ensures that any exposed conductive part of the appliance does not reach a dangerous level of potential or voltage that endangers the user's life. A proper earthing system should have least electrical resistance, good corrosion resistance and ability of dissipating high faulty current.
What is plate earthing procedure?
pipe earthing is done outside the tower, a hole of required diameter and depth is excavated and a pipe filled with coke and salt is put inside that hole which will be connected to the earth strip eventually connecting to the foot of the tower. The other method of tower earthing is counterpoise in which galvanised strip of wires is connected to the foot of the tower and is being earthed to a depth at some distance. Hope this answer work for you.. mohit sharma
Why should jockey not be pressed when it is moved in Carey foster's bridge?
When Jockey is pressed the length of conductor increases due to elasticity. Since resistance is proportional to length the resistance of the conductor also increases. So the voltage drop per unit length alters from its standard value. It causes error in our reading.
Can you run 1 HP single phase motor without neutral but with earthing?
Per code the earth should never be used as the sole source of ground. So no.
Give me reason why distance between two earth pits should be minimum 6metres?
because any two earthing points less than 6-8 meters will be a hazard rathar then being a safety measure as when there is a surge current or induced voltage on one point it would make a connectivity between the 2 earthing points.
What is standard earthing of electrical equipment?
i have a question? in the earthing system should we connect the negative pole of supply to the earth for example a +24 power supply?
Standard coffee table length?
The standard length of a coffee table can vary. This is because the length of a coffee table usually coincides with the length of the sofa it will be used with. The coffee table should be one-half to two-thirds the length of the sofa.
Why does an thick earthing wire?
A thick earthing wire, or a wide, flat conductor, is preferred, because it's more important to minimize henrys (inductance) in the earthing system than to reduce ohms (resistance). For the same reason, corners and small angles in an earthing conductor should be avoided, and the conductor should approach any connections from a parallel direction.
What is good earthing?
it is an trustwe should look after itmake it the best
What should you do if the specimen or object that you are measuring the length of is much smaller than the standard for length?
If the specimen you are trying to measure is shorter than the standard, you can use a different unit. After the measurement is completed, you can convert to the standard unit.
What is the effect of good earthing on power supply?
Good earthing ensures that should a short takes place in an electrical appliance, any charge is sent safely to earth.
How long should a golf driver shaft be if you are 5'11''?
Standard length will be perfect, standard length are usually 45.75" -46". But if you do feel the shaft is a bit short you could get half an inch or an inch added to it.
What is the standard length of time a 5 yr old should visit with their non custodial parent if that parent lives in another state?
There is no such standard.There is no such standard.There is no such standard.There is no such standard.
What types of electrical earthing systems are used in buildings?
Earthing is necessary for equipment safety and for human safety.Answer for USA, Canada and countries running a 60 Hz supply service.There are two types of earthing, they are:Plate earthing andPipe earthing.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What is the maximum length of a standard brick veneer wall before an expanssion joint is needed?
You should have an expansion joint every 20" or less.
How do I test my house's earthing?
Take 240V Lamp first check the voltage at Phase w.r.t neutral if lamp glows it means present voltage is OK now check the voltage w.r.t earth i.e. between phase & Earth point then lamp will glow. Now check between Neutral & Earthing Lamp should not glow. If these conditions are fulfill then your Earthing is OK.
What difference of derived quantities and standard quantities?
Derived quantities are quantities that you should be solving for. Ex: Volume, Mass etc Standard quantities are quantities that are specific. Ex: length, seconds, meter. Hop I helped you. :)
