What size bobbin is used in Kenmore model 385.1884180?
The Kenmore model 385.1884180 takes a Class 15 bobbin. They recommend plastic, but metal can also be used. Such bobbins are still generally available.
It depends on the model of the machine. If the bobbin is a top loading drop in bobbin, it's probably a class 66 bobbin. If the bobbin case is down below on the front of the machine, and you take it out to remove the bobbin, it's usually a class 15 bobbin. If you have your manual, it should tell you what bobbin you need. If you don't have your manual, go to managemylife.com, enter… Read More
Have the instruction book but does not mention so I have the machine and I would say same size as the singer but are metal OK ( bobbin ) Most Kenmore sewing machines (including this one) take class 15 bobbins which you can find at Joann's, Walmart, and most places that deal in sewing machines. They come in either plastic or metal.
You need a White Rotary bobbin. They are currently available (as of Dec 2011). You can get them through Quality Sewing in Tacoma, WA. Their website is QualitySewing.com but I do not know if they can be purchased through the website.
what year was this model (kenmore 363.9761585) built and what size is it?
Normally most 385.prefix kenmore use class 15 bobbins. If it's a drop in bobbin, they tend to prefer the plastic ones. You can find these at Joann's, Walmart(I just picked up a 4 pack of them at Walmart for 99 cents.) other sewing shops and through sears.com. Your manual should show you which bobbins to use and if you don't have the manual, you can download it at managemylife.com
22 cubic feet
According to Sears it is a 2003 model that was 22 cubic feet in size.
2005 i have one.
I believe it's 25.5 cubic feet
this is use gas or electrical
24.8 cuft, 2008 year model. Got one its great.
For Kenmore refrigerators, the 3rd digit after the decimal point indicates the capacity. Your model number would be written as 253.63894300. The 3rd digit after the decimal point is an 8. Your refrigerator is 18 cubic feet.
The washer was made in 1989.... The model number is read as the 1st and 3rd digits that represent the year made.
I did not have any luck with an online search, but I found that Searspartsdirect has a chat function where you could get an answer.
Attach the buttonhole foot. Set the setting for buttonhole (bh). Sew. You adjust the buttonhole size by sliding the rear part of the buttonhole foot forward and back.
Kenmore canister vacuum cleaners come in variety of models and can range in pricing from around $70 to nearly $300.00. The full size models vary in pricing from $200-$300, but the less popular colors may actually save you some money. The lime green model goes for nearly $100 less than the 'blueberry' model.
It is 22 cubic feet.
One Answer: If you look at the control panel on the door you can see that it's very similar to Whirlpool Gold control panels. I also asked sears.com chat person and he confirmed that it is Whirlpool. Whirlpool also makes: Kitchenaid, Jennair, Maytag, as well as Whirlpool. Second CORRECT Answer: As usual, someone just offers an answer and really doesn't do ANY research. Then accepts an answer from a salesperson as gospel! Wow, I'd like… Read More
Yes, you can take them out of the cabinet by loosening two grub screws that hold the machine on two posts. If the machine has a foot control, you are all ready to use it as a table top model. You can also put it in a Kenmore carrying case. Kenmores are a different size than other machines, so they have to go in a Kenmore carrying case or cabinet. If the machine has a… Read More
Kenmore made several washers over the years in the 80 series. The average size for capacity was 3.2 cubic feet of load space.
I have a Kemore Elite (model #596.76593600) The ice maker and water dispenser have stopped working. Would these be two seperate problems to fix or could there be one part to be replaced that would correct both problems?
A: It not size but rather capacity. the capacity will be the ac power consumption AC volts X AC current that will get Watts. So the capacity of the inverter should be the same watts plus a safety and efficiency power if the watts is 100 watts i would buy a 125 watts minimum
30 to 60 thread Free long bobbin Finest plated steel size 16 needles.
It is a model who is thin enough to be a Size 0.
I have a 1979 Kenmore dryer, and the belt is 92-1/4". It has 5 ribs/4 grooves, and measures at 5/16" wide, though it may have been 1/4" wide when new. Good luck -
What is the thread size for a Winchester Model 90?
Usually, XL is the most common plus size for the model. In these days, many companies are using size L model. Because it's hard to find XL female model with curve.
The frame size of a Smith and Wesson model 66 is K.
Instructions for making a working model will always include what the model is supposed to do in full size. Also needed is the size of the working model.
No year, make, model, or engine size and you expect an answer? No year, make, model, or engine size and you expect an answer?
40 or 42 or more
what model and engine ,tran size required what model and engine ,tran size required
Most sewing machines require bobbins, so you will most likely need one. Look up the specific machine to find out what size or type of bobbin is ideal.
You look at the Model number and you can then see the harddrive size for that model number at the PlayStation support network.
Make a normal model...except with bigger pieces! *Gasp!* So if you don't know how to make a doll sized model, I suggest you learn before trying to attempt the creation of a 'life size model'.
its sick, but.. 00-2. i used to be a model
Emme (Melissa) Aronson is credited with being the first plus size model to be recognized nationwide in the United States.
the average pants size for a model is 2
The size requirements for plus size models is between 12-18. Size 10 is sometimes used but not as often.
Hose sizes can vary depending on the vehicle manufacturer and model. Search for the hose size including the year and model should produce results.
Yes it does.
It is a model of anything lets say a building, that is the same proportions as the life size, except smaller. Meaning, it is the same thing scaled down. For example: the model is 1/4 the size. Or 1/10 the size.
it depends on the year, model, make and whatever size wheels are available.
For the LE model the factory size is: 215/60-16
The stock size for the GLS model is P195/65R15.
Since Saturn is considerably larger than Earth, you wouldn't be able to build a life-size model anywhere on our planet.