To get 24v from two 12v batteries you just link between ones positive and the others negative then connect your motor to the spare terminals, but your 12v charging system will not charge them (and any 12v equipment connected to them will burn out!) without removing the link.
You need to say whether it's a 150 amp service or a 1200 amp service it has to be one or the other. <<>> A 1/0 copper conductor with an insulation factor of 90 degrees C is rated at 155 amps. There is no ground wire stated for a 150 amp service so the next size up is a 200 amp service. The ground wire for this size is #6 bare AWG. Without knowing what types of loads that are coming off of the distribution a reduced neutral can not be recommended. The neutral will be the same size as the service conductor which is 1/0.
If the motor is operated from a three phase three wire distribution system the motor will not need a neutral wire.
12 AWG in most circumstances.
A motor can be reckoned at 1.6 kVA per horse-power, so on a 415 v 3-phase suppy the current for 20 HP would be 45 amps. For continuous use the wire size should be 25 mm2
There are several places where you can buy a Motorguide Trolling Motor. You can visit the Motorguide website, or you can purchase a Trolling Motor direct from specialist boat companies in your location.
How to calculate a cable size of 3kw motor
yes
It really depends on the state that you are in. There are different rules and regulations. In Kentucky, where I live, you have to license "anything" with a trolling motor no matter what (inflatable boat, canoe, etc.) It seems kind of silly though!
12
typically if the vessel is over 12 feet long, you need to register. even though there is no gas motor.
Depends on the current rating which should be on the motor.
If you bass fish or have seen a bass boat, you have probably noticed the small propeller on a pole in the front of the boat. This is the trolling motor.Trolling motors - Not just for trollingTrolling is the art of covering a large amount of water in a short time. Basically, the boat moves across the water, dragging angler's lures through the water. Various lures at various depths can be used but the principle is the same, fish as much area as possible.A trolling motor is an ancillary motor to the large one that fully propels the boat. Normally at the front of the boat, the trolling motor is used for slow presentations. Crappie fishermen use trolling motors in this way. Since they use multiple rods with lures at several depths, a trolling motor allows them to fish slowly and methodically.The trolling motor for bass anglersBass anglers and in particular tournament anglers, make heavy use of the trolling motor. The trolling motor is not used to troll, but rather to move the boat from location to location slowly and silently. Bass anglers fishing tournaments must cover large amounts of water to be successful The trolling motor allows them to do that. Since the trolling motor is electric, it does not make noise that will spook fish, another key element for the tournament angler.Going where angels fear to tread - Getting back thereThe large outboard on the back of the boat is great for navigating wide, deep, open bodies of water, but what about that honey hole in the very back of the lake? You know the one that is choked up with vegetation, stumps and shallow water? Getting there with the outboard is impossible if not dangerous, but the tournament purse may lie on your ability to get to that area. Good thing you have a trolling motor.The trolling motor will get you into tight spots that the large motor cannot. Shallow water, stumps or vegetation can be trouble for the big outboard motor, but the trolling motor can work right through it. If the trolling motor does get choked on weeds, cleaning it is a snap since you only have to lift it out of the water.
Wire size for any piece of equipment is based on the equipments load amperage. The higher the amperage that larger the wire size has to be. For motor loads the motor's amperage has to be increased by 25% to size the conductor. Example, a 10 amp motor load current plus 25% equals 12.5 amps. This would boost the wire size from a #14 to a #12 conductor. This additional amperage increasing is also used for transformer conductor sizing.
20LBS
The motor has a plate on the head or the handle with the model number on it.
The motor has a plate on the head or the handle with the model number on it.