0
What size wire should be used to connect a dryer to electrical panel?
Wiki User
∙ 11y ago
That depends on the dryer. Some have natural gas capabilties and use a standard 120V outlet (20 amp dedicated circuit). Others operate strictly off of electricity and use a 230V power source. These use a somewhat standard dryer outlet that conforms to the plug from the appliance, and are usually (but not always) 30 amps. In the case of the former you would use a 12 gauge wire with 2 conductors (hot and neutral) and a ground. The latter would use a 10 gauge wire with 3 conductors (2 hot wires and a neutral) and a ground. Always refer to the appliance specs to determine how the appliance should be wired, and find a qualified person to install these outlets if they don't exist.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Can you splice wires in an electrical panel?
yes wires is electrical panel
How do you complete a sentence that begins with 'Electrical wire sheathing should not'?
Electrical wire sheathing should not project more than about one inch into the electric panel.
What brand of electrical panel box is compatible with Gould brand breakers?
Siemens bought Gould so a Siemens panel should work.
Is condensation near an electrical panel dangerous?
O course it is very dangerous. Moisture should never ever be allowed near a service panel.
Can you wire a external and an internal ground together on a drier?
The ground wire should go from the dryer directly back to the distribution panel. An external ground wire is not required. The ground wire that is in the cord set that is connected to the frame of the dryer and the ground wire that is in the feeders coming from the distribution panel, that is connected to the ground terminal in the dryer receptacle, is all that is required to satisfy the code requirement.
How close can a gas dryer be to an electrical panel?
A space of 30 inches or the width of the electrical equipment is needed, whichever is greater, for electrical equipment.
Where is the double 30 amp breaker in an electric dryer?
It should be in the main circuit panel. If the dryer was added at some point there may be a separate box just for the dryer either beside the main panel or at the dryer plug. It is not in the dryer itself.
Can you install 200 amp service Panel in washer Dryer closet?
No, you can not install a service panel in a washer/dryer closet. The National Electrical Code (US) requires you to maintain work space in front of the panel (3' deep and 30" wide)
Where is the data plate located on a trailer home?
Usually near the electrical panel, or in the utility (washer and dryer) area.
How do you wire a three wire 220v for dryer White to white but where does black and ground go?
If the cable you are trying to connect the dryer up to only has a white, black and ground wire, then the dryer is not going to work. The cable needs to be a three wire, the ground wire is never counted when discussing house wiring. Open up the electrical access panel on the back of the dryer. You will see a terminal block. A red and black and white connect to this terminal strip. The "hot" wires are connected to the outside terminals. The neutral (white) wire will be in the center. Connect the ground wire to the frame of the dryer. It is very important that this ground wire be connected as this is the wire that carries the fault current to trip the breaker should a fault arise.
Can groundwire be together with neutral wire at the dyer?
Ground and neutral should only be connected at the main electric panel to prevent parallel neutral currents. If it is a new installation, you must provide four wires (two hots, 1 neutral, & 1 ground) and connect to the four separate (appropriate) places on the dryer. If it is an existing installation and it only has three wires (two hots and a neutral) connect the neutral to both the neutral and ground connection of the dryer (the National Electrical Code allows this exception for older homes). Call a qualified electrician to do any electrical work.
Where does ground wire connect to gauge panel on 1981 corvette?
there is no ground in a car electrical system.
What should the Electrical panel rating be no smaller than?
the main breaker
Why should you balance an electrical panel?
To keep the current on the neutral to a minimum.
Can you splice wires in an electrical panel?
yes wires is electrical panel
What is the answer to in a typical home electrical panel installation the ground wire is connected directly from a geound rod driven into the ground to the?
Connect other end to the ground lug in the service entrance part of your panel.
Electrical wire sheathing should not project more than1 inch into what A floor joist B electric panel C ground D plumbing line?
B. Electrical panel
