0
What else can I help you with?
Where do you takes your 2006 dodge charger for transmission recall?
To the nearest Dodge dealer.To the nearest Dodge dealer.
What type refrigerant 2008 dodge charger?
It takes R-134
Where is the manufacturing plant for a dodge charger?
Final assembly takes place in Brampton, Ontario, Canada
What type transmission fluid do you use in 1966 dodge charger 727 transmission?
It takes just regular tranny fluid.
How do you remove the crank sprocket on a 2006 dodge charger 2.7?
After you remove everything required to get to it, it takes a special tool to pull it off the crankshaft.
What grade of gas dodge charger rt takes?
The R/T has the hemi so it takes premium gas. My HEMI, from the factory, took mid-grade. (So, 89 octane)
Dodge 1998 front axle nut size?
The axle shaft nut takes a 1 and 11/16 inch socket
What tools are needed to change the front brake pads on a 1998 Dodge Caravan?
1/2 wrench or 1/2 socket and ratchet and that's basically all it takes
What could cause your cell phone charger to blow two 20 amp fuses in a 2005 Ram 1500 when the charger's 2 amp fuse is fine?
Clearly the high current problem is not going "through" the 2 amp fuse, so, it's not going through the charger itself. One possibilty is the lighter socket itself and the way the charger fits it. That particular charger may fit in the socket so that it causes a short when you plug it in. Physically it's connecting the outside and the center of the socket (+12V) together. A 12 Volt socket is no marvel of engineering, it's barely adequate for connecting anything to but it became a standard anyway. The fit of each socket varies from one vehicle to the next, it's not supposed to be able to short under use but I've seen it happen. If that's the case you need to adjust the way it fits, replace the socket, etc. Another possibility is the way the center wire moves "behind" the socket when you plug something into it. The center wire gets pushed back in a little and may come in contact with a ground and pop! There goes the fuse. You can determine what is going on by looking at the socket and the end of your charger where it plugs in. Blowing 20 amps fuses takes quite a bit of current so most likely this would leave a mark on whatever metal was in there causing the short. Check for a very small burn mark on the tip of the charger. If there's a mark then you know which part was touching where it shouldn't be. Also check that no foreign object fell into the socket like a tiny piece of metal. If you want to check out the charger itself try it on another vehicle or get some wire, put a 2 amp fuse in-line with it and connect the charger to any 12V DC source. Make sure you get the polairty correct, usually the center post is positive, and the outside is negative. When you connect it nothing should happen other than the charger turns on. If it blows the new in-line 2amp fuse then there is a problem with the charger itself but that's not likely. I think the charger is shorting the vehicle socket when you plug it in. Dave
How long does a portable charger take to charge?
This depends on what kind or charger are you asking about and what kind of battery are you charging. My Phone charger takes two hours to charge my phone.
How long does it take to charge a portable charger?
This depends on what kind or charger are you asking about and what kind of battery are you charging. My Phone charger takes two hours to charge my phone.
How long does it take a Dodge charger mopar to go 0 to 60?
The time it takes for a Dodge Charger equipped with Mopar performance parts to accelerate from 0 to 60 mph can vary depending on the specific model and modifications. Generally, high-performance variants like the Charger SRT Hellcat can achieve this in around 3.6 seconds, while other models may take between 5 to 6 seconds. Factors such as engine type, weight, and road conditions can also influence the acceleration time.
