To be exact, you are supposed to change your clock to 1:00 A.M. the minute after 11:59 P.M. on the night of daylights savings time. (So you are skipping the hour of 12:00.) But if your like me, and don't like staying up to midnight to change the clock, you can just change it right before you go to bed.
how to time set up ajantha degital clock model no: olc 103
It wakes you up at the time you set it to
60 (minutes per hour) x 60 (seconds per minute) = 3600 (seconds per hour).
there are 2 knobs at the back and one has a bell. that's the one you turn to the time you want to wake up or the time you want it to sound.
On the back there should be an alarm set knob (the one with the picture of a bell). On the face of the clock there should be a small, red, short, extra "hand" that doesn't move with the time; that's the alarm setting. Holding the face towards you, turn the alarm knob on the back until the alarm hand points to the time you want the alarm to go off, based on where the hour hand would be (remembering that the hour hand of an analog clock moves slowly between the numbers of this and the next hour, so 6:30 would be halfway between the 6 and the 7). Then there must be a way to turn on/off the alarm. Set this to on before you go to bed at night. In the morning when you wake up you will set this to off to stop the alarm. Don't turn it back on until before you go to bed, or else it will go off at the PM, not the AM, version of the alarm time.
Press and hold the clock button to the left of the display until the selection for 12 or 24 hour time comes up (note 24hr time is military time)...after selecting 12 or 24h, the hour should be blinking, press set for each hour to increase, press clock to change to the minute selection and press set to increase the minutes, press clock when you are done.
how to time set up ajantha degital clock model no: olc 103
Go to set up screen scroll down to clock press the on the screen number will pop up set time
set time timex t123s
how to set clock on jvc kd s-640 CDpress an hold the select for more than two seconds clock H will appear use the volume up and down buttons to set hour. use the up and down tuning buttons to switch from hour to min.
It wakes you up at the time you set it to
Assuming you mean the clock in the radio display. turn on radio, Press the RDS control button until it Clock Hour is displayed then use the SEL control (up/down) to set the hour. The Clock Minutes is the next item in the RDS control display. Use the SEL control to set the minutes while in the Clock minutes mode.
How to change Mazda 3 Clock settings To set the hour: 1) Put ignition in ACC or ON position 2) Press and hold "CLOCK" until beep sounds and "12 hr/24 hr" is displayed; 3) Press "SET" to select 12 or 24 hours (24 hours is military time) 4) Press "CLOCK" again while the selection is flashing "Hr ADJUST" 5) Press "SET" to select hour 6) Press "CLOCK" when done Do the same to set minutes, but select Minutes in step 4
hold set button then hit scan for mins. and seek for hour. then hit set
1. Press the 'CLOCK' button to bring up the clock mode. 2. Press and hold the 'Clock' button for 4-6 seconds and the clock display will start to flash. 3. Use the 'HOUR', 'MINUTE', AND 'SECOND' buttons to make adjustment to the time. 4. When finished with the adjustments, press 'CLOCK'.
click on the audio button to select clock and press to toggle from hour or minute you want to set and press + or - to select the number. To cancel set up, click band button.
With key on and stereo off hold both the clock and audio button clock reading will blink use up and down arrows to change hour then left and right to switch to minutes up and down to set press clock button again and done