0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Does an iron burn have to blister to heal?
an iron burn can cause wound which requires air to heal
How do you properly clean the joints to be soldered?
There are several ways of soldering electrical joints. Automated methods use wave soldering in which a circuit board is passed over a bath of solder. Re-flow soldering uses solder paste that is applied to the circuit board and then heated in an oven until it melts and flows across the joint. Manual soldering is largely still carried out with hand held soldering irons. The standard technique is to apply the tip of the iron to the joint and then feed solder onto the joint as the iron heats it. This method allows the solder flux to flow around the joint before it is affected by the heat. Applying the solder to the iron before touching the joint will often result in a dry joint because the flux will burn away and evaporate before it reaches the joint. Most electronic components have limits for the amount of time the soldering iron can be in contact with each pin. Generally it is in the order of 5 or 6 seconds. With the introduction of lead free solder, temperatures need to be higher to get a good joint and therefore the contact time with each component is reduced. With a shorter contact time, it is even more important to heat the joint and apply solder in an efficient manner. Production and commercial soldering skills take years to develop with apprenticeships lasting up to three years. To describe soldering techniques in just two or three paragraphs is to merely scratch the surface. Although there are many written instructions for soldering joints, there is no substitute for practice and learning from skilled wiremen.
Can you safely turn a soldering iron off and on with a motion sensor?
Soldering Irons don't heat instantly so if that is the goal, yes you can but you will still have to wait for it to warm up. From a practical safety standpoint, I personally would not do it.
Can an iron burn cloth?
Yes it can
Why is oxygen blown through the molten iron?
to burn coke that will burn the raw material
What are the dangers of using a soldering iron?
you can burn yourself or burn someone else. you must always be careful.
Why do you think it best for soldering iron to have its soldering stand?
why do you think its best for soldering iron to have soldering stand
What is soldering iron and how do you use it?
Soldering iron is used in heating the metal for soldering. If you want to learn more about soldering iron visit en.wikipedia.org/wiki/Soldering_iron.
Where can I go to get some information on soldering iron?
When you use a soldering iron you would be soldering some kind of metal frame or something because soldering irons are irrelevant to soldering iron. Sorry, not applicable.
What is the definition of soldering stand?
soldering iron stand use for the electricians to easily the soldering iron make stand
What type of soldering iron do you need to do a mod on a Wii nunchuck?
a good one;
Why do you think it is best for a soldering iron to have a soldering stand?
Have you ever had a soldering iron roll off the table and land on your wrist, burning a hole that took over a month to heal? I did in 5th grade while building one of the Radio Shack electronics kits I had received for Christmas! Learning from that I made my own soldering stand from a small metal can and poured over a half inch of lead into the bottom from my lead soldier casting set to make sure that the weight of the soldering iron could not tilt the soldering stand!!! I was never going to run the risk of a soldering iron getting away from me again!!!!!
What is iron tin?
Tinning the Soldering iron is when the hot iron is coated with solder to aid in soldering and heat transfer
Characteristic of soldering iron?
Soldering iron is characterized by having the melting point of the filler metal.
What is the difference of a soldering iron and a soldering gun?
A soldering iron is a straight tool, sort of like a long screwdriver. A soldering gun actually looks like a gun or a drill.
What kind of tools are included in a soldering iron kit?
A soldering iron kit includes a soldering iron, a soldering iron stand, a sponge, diagonal cutters, long nose pliers as well as wire strippers. This example aplies only to sets for beginners.
Where could one purchase a butane soldering iron?
One can purchase a butane soldering iron at Amazon, eBay and many technique stores both online and as retailers. A butane soldering iron is a hand tool used in soldering.
