Want this question answered?
If what you are talking about is the small cylinder shaped one, just push in the round recessed button on top with a pen or something.
Some breakers must be turned all the way to the OFF position after they have tripped.Before you spend a lot of money, just flip the breaker all the way to the off position THEN try to turn it back on.Other answersIf this circuit breaker is a GFCI or RCD and it won't reset when you press its RESET button, it is doing its job.It is telling you there is something wrong in the circuit it is protecting.It may be a fault within an appliance (or its flexible cord or its plug) that is plugged into a socket outlet on the circuit being protected by the circuit breaker.To find out, disconnect all appliances on the circuit and then press the RESET button. If the breaker no longer feels spongy then you know if is not a fault in the circuit wiring.Then press the TEST button on the breaker. If it immediately trips then you know that the breaker itself is not faulty.Then press the RESET button again and re-connect one appliance at a time until you find the one that causes the breaker to trip off. That is the appliance (or its flexible cord or plug) which has a fault that is causing the breaker to trip. The fault will have to be repaired - or the appliance will need to be replaced - before the circuit breaker can be reset with that item connected to the circuit.Sometimes a fault can develop inside a socket outlet and there is now a "Neutral-to-Ground" short, or even a "Live-to-Ground" short, in the wiring to the outlet. Usually such shorts occur in the wall box behind the outlet because the wiring was done carelessly. Such a fault will also prevent a GFCI or RCD from being reset. That kind of fault must be fixed before the circuit breaker can be reset.If it is a regular circuit breaker it might be that the breaker is mechanically defective.For more information click on the links to the Related Questions shown below.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
You may have to locate the fuse box or circuit breaker box and reset or replace whats needed. Most outlets dont need to be reset unless they have little buttons on them, meaning it is a GFCI outlet - in which case it will have a little button that says reset on it.
If your smoke detector is bleeping you have a serious risk of fire and the circuit breaker must not be reset until the fault that caused it to trip is investigated.
A circuit break will reset until it mechanically breaks down. What you should be looking at is why is the breaker tripping all the time. A breaker is a safety device that stop current from overloading the wire that it is protecting. When the breaker trips check and find out what other devices have stopped working. Total up the wattages. If the total is above 1500 watts then something is going to have to be disconnected on that circuit.
You reset a circuit breaker by pushing the reset button.
Have the circuit breaker replaced.
Most automotive circuit breakers reset themselves after they cool off. Some bigger trucks use circuit breakers that are reset manually. They have a button you push in to reset the breaker after it has cooled off.
Most automotive circuit breakers reset themselves after they cool off. Some bigger trucks use circuit breakers that are reset manually. They have a button you push in to reset the breaker after it has cooled off.
The only control on a circuit breaker is its on/off/reset lever or button.
A manual circuit breaker must be reset by hand, as opposed to an automatic circuit breaker, that may be able to reset itself once it cools down.
You should replace the surge strip if the circuit breaker fails to reset.
Where is the fuel pump inertia circuit breaker located on a 2008 Toyota Corolla
You can reset a circuit breaker but a fuse you must replace.
The reset button only resets the built in circuit breaker in the power strip section of the surge protector. If it quit working then you may have pressed it too hard and broken the circuit breaker's mechanism (this is hard to do but possible) and the device is now scrap. Replace it with a new surge protector.Pressing reset by accident is really very unlikely to break the circuit breaker's mechanism, but I didn't see what you did.
A circuit breaker is an overcurrent device that can be reset after it has opened.
The reset is part of the resettable circuit breaker. It is located just below the "not grounded" light that indicates when a ground is not present