0
A blown fuse creates an "open" circuit condition. It's the same as opening a switch [turning a switch to the off position].
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is used in an electrical circuit to prevent a short circuit?
difference between p type and n type semiconducter materialAnswerInsulation is used to prevent a short current. To protect the circuit should a short-circuit fault occur is either a fuse or a circuit breaker.
What do you do when you've blown a fuse?
A fuse is a deliberate weak link which will be blown if there is a power overload. When you blow a fuse, take the blown fuse out and throw it away as you would a blown light bulb, and replace it with another fuse of the same type. * In the old-timey fuse boxes a penny could be substituted for a fuse, but a penny is too strong to be blown, and the next overload will burn the house down.
How can I tell if a fuse or circuit breaker is blown in 97 trans sport?
Circuit breakers are difficult as there is not an otside way to tell if they are bad. The plastic blade type fuses are easy pull out the offending one and look through the plastic at the top to see if the wire is broke or not. If it has a space in the wire the fuse is bad.
What number is fuse for interior light on Jaguar s-type?
its probably the blown fuse I'd be guessing
What type of circuit has little to no resistance and will usually blow a fuse?
there are three types of circuits. Series,parallel,parallel-series. Series circuits usually are involved with dimming lights, and blown fuses.
1992 beretta has no dash lights?
Check the fuse it might be blown,if so replace with same type fuse
Whats the difference between a switch fuse and a fused switch?
A fuse's main purpose is to quickly disconnect a short circuit from the distribution system. A circuit breaker has a twofold function: it trips on a short circuit by utilizing a magnetic sensor device and it also trips on a thermal device which senses a current overload that is higher than its rated current. Both devices are housed inside the breaker case.Fuse: When the current passing through a fuse exceeds its rated value it physically burns through a thin strip of metal and opens the circuit so current can no longer flow. You have to get a new fuse to restore operation.Circuit breaker: When a circuit breaker trips it opens a mechanical switch to interrupt the flow of current. You just need to reset the breaker and you are ready to go again.In both cases you must always be sure to remove the cause of the over-current situation because, if you don't do that, the effects of a blown fuse or a tripped breaker will continue!Fuses and circuit breakers were invented to protect electrical items from being damaged by taking too much current (amps), something which is also known as an over-current fault condition.FusesHow a fuse worksWhen an over-current fault condition occurs, which is the same as saying the current gets bigger than the fuse can carry, its internal "fuse wire" gets so hot that it melts and breaks apart, which cuts off the supply of current. When that happens the fuse is said to have "blown".After whatever caused the over-current fault condition in the circuit has been repaired, a blown fuse must either be replaced with a new one or, if it is the type of fuse which can be rewired, it must be repaired using the correct size of special "fuse wire".A new fuse should then remain in place un-blown until another over-current fault condition occurs in the circuit it is protecting, which would then cause the new fuse to blow.What are the advantages and disadvantages of fuses?To give the same over-current protection, fuses are generally cheaper to make and smaller in size than circuit breakers.However an ordinary fuse cannot blow as quickly as a circuit breaker can "trip".Some equipment may require special "quick-blow" fuses so that damage can be prevented when an over-current fault condition occurs. Quick-blow fuses cost much more to make than ordinary fuses but must sometimes be used where a circuit breaker would be too expensive and/or too large in size.Further notes about fuses:Some fuses are rewireable, meaning they can be repaired if they blow. This must only be done using new fuse wire of the correct size. It is dangerous to use fuse wire which is thicker than the size marked on the rewireable fuse's body.Other fuses, known as "one-time" or "cartridge" fuses, cannot be repaired when they blow. If that happens they must be thrown away and replaced by a new fuse of the correct size. Some one-time fuses look like small cylinders with a metal cap at each end; others look like a small cylinder with a metal screw-cap on one end like a light bulb. One-time fuses for vehicles, known as "fuse-links", have small bodies made of plastic and two metal blades which push into fuse slots in the vehicle's fuse box.If a one-time fuse blows it should only be replaced by a new one of the correct size (Amps) for the circuit. The ones which screw in have different sized screw-caps for each size of fuse, with matching sockets to ensure that only a fuse which is the correct size can be screwed into the fuse holder. Similarly, fuse-links have different sized metal blades and matching slots to ensure that a given slot can only accept the correct size of fuse link.Circuit breakersHow a circuit breaker worksWhen an over-current fault condition occurs, which is the same as saying the current gets bigger than the circuit breaker was designed to carry, it's mechanism causes its switch contacts to open, which cuts off the supply of current. When that happens the circuit breaker is said to "trip".When whatever fault condition in the protected circuit has been repaired, the circuit breaker can be "Reset" by pressing a button to close its switch contacts. The contacts should then remain closed until another over-current fault condition occurs in the circuit it is protecting, which would cause the breaker to trip again.What are the advantages and disadvantages of circuit breakers?To give the same over-current protection, circuit breakers can be designed to trip much faster than an ordinary fuse but they are generally larger in size and cost more to make.However circuit breakers are re-usable and can easily be reset after they have tripped - provided, of course, that the fault condition in the protected circuit has been repaired.A fuse is a protective device that destructively opens when the current flow exceeds a preset value. It is usually designed as a low value resistor that heats up and melts at the specified current value. Once the fuse blows, it must be replaced.A circuit breaker is a protective device than non-destructively opens when the current flow exceeds a preset value. It is usually designed as a tripping relay/switch that can be reset and reclosed when the fault is cleared.In both cases, the design can provide for different preset values as a function of time. It depends on whether the intended load pulls a larger startup current than when it runs, such as a motor, which can easily pull four times their run current when they startup. The protective device is selected for the specific type of load, and for the rating of the conductors supplying it.
What type of fuse do you use to get your heater to work in a 1996 Mazda protege Lx?
Use the exact same size, shape and color fuse as the blown out one you removed from the fuse box
What are the different kinds of electrical receptacle?
The most common types are the regular type, where the only over current protection is provided by the breaker panel. the other most common type is the GFCI (Ground Fault Circuit Interrupter) This type has a built in "circuit breaker" so when it senses a fault in the circuit it trips-this type is the safest as they are more sensitive than circuit breakers in the breaker panel.See related links below.
What is the name of the device that protects a circuit from current overload?
It is called fuse or circuit breaker.In electronics and electrical engineering, a fuse is a type of low resistance resistor that acts as a sacrificial device to provide over-current protection, of either the load or source circuit. Its essential component is a metal wire or strip that melts when too much current flows through it, interrupting the circuit that it connects. Fuses are an alternative to circuit breakers.A circuit breaker is an automatically operated electrical switch designed to protect an electrical circuit from damage caused by overload or short circuit. Its basic function is to detect a fault condition and interrupt current flow.Unlike a fuse, which operates once and then must be replaced, a circuit breaker can be reset (either manually or automatically) to resume normal operation.
Rear heated window not working what could be wrong with it?
Blown fuse or a break in the wiring. There are kits to repair that type break.
What type fuse does Chevrolet S10 pickup truck use?
"Spade" fuses, what size depends on the circuit.
